Marantz SR6400 manual Other Function, Attenuation to Analog Input, Signal TV Auto ON/OFF Function

OTHER FUNCTION	ATTENUATION TO ANALOG INPUT
	SIGNAL
TV AUTO ON/OFF FUNCTION
This function allows the component connected to				VOLUME
the TV-VIDEO in jack to control the power (ON/
OFF) to the SR6400.	F/P	MODE	DOWN	UP
AUTO POWER ON			MUTE	ATT

VIDEO ON/OFF

When no video signal is connected to the SR6400 or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the “VIDEO OFF” setting.

To select video off, press the V-OFFon the remote.

UND RECEIVER SR6400

SELECTING ANALOG AUDIO INPUT					ENGLISH
OR DIGITAL AUDIO INPUT
ROUND RECEIVER SR6400
CLEAR	MEMORY	TUNING	F/P	MODE
ENTER
TVDVD	VCR1	DSS/VCR2 AUXCD-R	TAPE	CDTUNER

1. Be sure the TV auto mode is ENABLED.

(Refer page 17 : System Setup)

2. Connect your TV TUNER (etc) to the TV-VIDEO in terminal. Be sure to connect the VIDEO input.

3. Turn OFF the power to the TV TUNER and the

SR6400.

4. Turn ON the TV TUNER and tune in a receivable

station.

5. When the station is received, the SR6400 turns ON and TV is selected automatically.

AUTO POWER OFF

1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.

2. The power to the SR6400 switches to STANDBY

after approx. 5 minutes.

CD-R TAPE CD TUNER

AUX INPUT

If the selected analog audio input signal is greater than the capable level of internal processing, the “PEAK” indicator will light up on the front display. If this happens, you should press the ATT button on the front panel or on the remote.

“ATT” indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD-R/MD- OUT, VCR1-OUT and DSS/VCR2-OUT.

This function is memorized for each individual input source.

CLEAR MEMORY TUNING F/P MODE

TER

TV DVD VCR1 DSS/VCR2 AUX CD-R TAPE CD TUNER

ONES

DISPLAY MODE

AV SURROUND RECEIVER SR6400

CLEAR MEMORY TUNING F/P

ENTER

TV DVD VCR1 DSS/VCR2 AUX CD-R TAPE CD

PHONES

PHONES

If you have already assigned the digital inputs, you can temporarily select the audio input mode for each input source with the A/D button on the remote controller or front panel.

When this button is pressed, the input mode is switched in the following sequence.

→Digital Auto → Digital → Analog → Digital Auto....

In Digital Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically.

In Digital mode, input is fixed to an assigned digital input terminal.

In analog mode, the analog input jacks are selected. This selecting is temporary, so the result will not be

stored in memory.

•AUTO POWER OFF is canceled if the SR6400 is set to a source other than TV.

The function reactivates when TV is selected again.

•Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON.

•The S-Video terminal does not support “TV AUTO ON/OFF” function.

This jack may be used to listen to the SR6400’s				You can select the display mode for the front display
output through a pair of headphones. Be certain that
				of the SR6400.
the headphones have a standard 1/4" stereo phono
				To select this mode, press the DISP. on the remote
plug. (Note that the speakers will automatically be
				control.
turned off when the headphone jack is in use.)
				When this button is pressed, the display mode is
	AV SURROUND RECEIVER SR6400			switched in the following sequence.
	SELECTOR			→ Surround Mode → Auto-display Off → Display
				Off → Input Function → Surround Mode....
	CLEAR	MEMORY	TUNING	In Auto display off mode, the display is off. But, if
SELECT	ENTER			you make a change to the unit such as input or
POWER ON/STANDBY	PHONES	VCR1	DSS/VCR2 AUX	surround mode, the display will show that change,
	TVDVD
				then go back to off after about 3 seconds. When
				changing the volume, it is not displayed.
				In Display off mode, the display is off completely.

Notes:	Notes:
• When using headphones, the surround mode will
	• Only the DISP indicator will be illuminated on the
change to STEREO and TruSurround (TS)
	front display in display off condition
headphones by SURROUND MODE selector.

•The surround mode returns to the previous setting as soon as the plug is removed from the jack.

If you need to change the input mode completely, use SYSTEM SETUP in OSD menu system. (see page 16)

23