Marantz Essential Guide for Operating Your SR7400 Stereo Receiver
Page 36

BASIC OPERATION

USE MODE

(Normal operation status)

This remote control is preset with a total of 12 types of remote codes, including Marantz TV (television), DVD, VCR (VCR deck), DSS (satellite broadcasting tuner), TUNER, CD, CD-R, MD, TAPE (tape deck), AUX1, AUX2, and AMP (amplifier).

Learning is not necessary for Marantz products. You can use these products without setting any codes.

1. Press the SOURCE button.

For this example, press DVD.

DVD is shown on the LCD, and the remote control is set for DVD.

Pressing the source button once changes the remote control to the settings for the source that was pressed.

To change the amplifier or other source, press the SOURCE button twice (double-click). The code is sent, and then the amplifier source changes to DVD.

2. Press the buttons to operate the DVD.

Theindicator is shown on the LCD while the remote control codes are being transmitted. It is not displayed when buttons without stored code are pressed.

3. The direct buttons can be used to perform up to 20 operations for each of the 12 sources, including DVD, TV, AMP, and other AV equipment.

The buttons consist of the D1 to D5 buttons, and the equipment is operated by pressing the buttons corresponding to the indicators on the LCD.

Four pages are available, and press the > button to select a page. The current page position is displayed on the LCD.

PRESET MODE

(When operating non-Marantz AV equipment products)

This remote control is preset with remote control codes from AV equipment by other manufacturers. The preset codes are TV, VCR, LD, CABLE, DSS, DVD, TAPE, TUNER, CD, CD-R, MD and AMP. Settings can be made in one of two ways.

When the preset codes are set, the following codes are contained in the source button of the remote control.

See the attached manufacturer number list for the preset manufacturers, devices, preset numbers, and other settings.

Remote control

Corresponding

Device name

source name

preset code

 

TV

TV

Television

DVD

DVD

DVD player

VCR

VCR

Video deck

DSS

SATELLITE

Satellite broadcasting

 

 

tuner equipment

TUNER

RECEIVER/TUNER

AM FM TUNER

CD

CD/CD-R PLAYER

CD player

CD-R

CD/CD-R PLAYER

CD recorder

MD

CD/CD-R PLAYER

MD deck

TAPE

TAPE

Cassette deck

AUX1

CABLE

Cable television

AUX2

LASER DISC

Laser disc player

AMP

AMPLIFIER

Amplifier or receiver

 

RECEIVER/TUNER

 

•When using Marantz products, TV and DVD can be set to TV1 (TV/VDP: Projector) and TV2 (PDP: Plasma display), and DVD1 (first DVD player) and DVD2 (second DVD player), respectively, to match the customer’s operating environment. These settings are made in PRESET mode.

In the factory default state, the remote control is set to TV1 and DVD1. To make the presets, enter the numbers below while referring to the section “Entering and Setting the Manufacturer Number Directly”.

TV1: 0001, TV2: 0002

DVD1: 0001, DVD2: 0002

Entering and Setting the Manufacturer Number Directly

Refer to the manufacturer number list.

This example shows how to set a SAMSUNG DVD player.

2

3

4

 

LEARN

LEARN

USEPAGE 1

1 2

1 2

56

LEARN

LEARN

1

2

1

2

1. View the supplied manufacturer number list, and find the number of the manufacturer for the device that you are using.

2. Hold down the M button for three seconds or more.

The menu is displayed.

3. Press the D1 (PRESET) direct button. The Preset setting (P-SET) is displayed.

4. Press the DVD source button.

5. Press the numeric buttons to enter the four- digit manufacturer number.

Example: To enter “0600” from the manufacturer number list.

To correct the entered number, use the or cursor button to enter the correct number.

•If no button is pressed for over one minute during the setting process, any settings that were made are cancelled.

6.Press the OK cursor button.

7.Confirm the OK is displayed and then the display returns to the Preset Setting (P-SET).

When the manufacturer number is entered correctly, OK is displayed momentarily on the screen.

• I f y o u e n t e r a n u m b e r n o t i n t h e manufacturer number list, WRONG CODE is displayed, and then you return to the preset setting again

Check the manufacturer number list, and either set a different number or use the sequence function to set.

8. To set the manufacturer number for another source device, repeat the procedure in steps 4 to 6.

9. After the settings are completed, press the M button.

10. Press the buttons on the remote control to check that the DVD can be operated correctly.

Setting Equipment Not Appearing in Manufacturer Number List

Use the sequence function to set equipment not appearing in the manufacturer number list. You may still be unable to set some equipment even when using the sequence function. In this case, the remote control can be programmed with codes individually.

In the sequence function, the power ON/OFF codes are transmitted by pressing the remote control buttons in order.

If the power for the equipment is left on, hold down the button until the equipment is turned off, and then release. This completes the setting.

This example shows how to set a DVD player.

ENGLISH

4

 

 

5

 

7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

LEARN

 

 

 

LEARN

 

 

LEARN

 

 

 

 

1

2

 

1

2

 

1

2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.

Turn on the power of the DVD player.

 

 

 

2.

Hold down the M button for three seconds or

 

more.

The menu is displayed.

3. Press the D1 (PRESET) direct button. The Preset setting (P-SET) is displayed.

4. Press the DVD source button.

5. Hold down the CH+ or CH– button for one second or more.

6. Press the CH+ button repeatedly in the interval for one second.

The signal is transmitted, and the display cycles through the code number.

Press the CH– button to go back to a number screen.

7. Release the button once the DVD player turns off.

8. Press the OK cursor button.

9. Confirm the OK is displayed and then the display returns to the Preset Setting (P-SET).

10. To set the manufacturer number for another source device, repeat the procedure in steps 4 to 8.

11. After the settings are completed, press the M button.

12. Press the buttons on the remote control to check that the DVD can be operated correctly.

Check the following points if the equipment which was set does not operate properly.

•If there is more than one number in the manufacturer number list, try setting a different number.

•There may be some buttons which cannot be used. Program the codes to the required buttons.

33

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Model SR7400 User Guide Outlet before cleaning. Do not use liquid Cleaners or aerosol cleaners. Use a dampCloth for cleaning Product may fall, causing serious injury toPower-Cord Protection Power-supply cords Product during a lightning storm, or when it isLightning and power-line surges Power Lines An outside antenna systemTable of Contents Precautions IntroductionDescription About Dolby Pro LogicFeatures AccessoriesRemote Controller RC1400 Input Function Selector FL Display PCMRear Panel SBR, CWhen AMP mode is selected Names and FunctionsAudio IN/OUT CD, TAPE, CD-R, TV, DVD, VCR1, DSS/VCR2 Digital Input Dig.1 6 / Output coaxial, opticalLCD Indicators Remote Control Range Battery Replacement IntervalSafety Precautions for Batteries Loading BatteriesSetting the Time General Information of RC1400Speaker Placement Connecting SpeakersConnections Connecting Audio Components Banana plug connections are also possibleTighten the knob by turning clockwise and then Insert the banana plugConnecting Video Components There are 3 types of video jacks on the rear panelVideo jack Component jackConnecting Multi Channel Audio Source Connecting AN External Power AmplifierSacd Multi Channel Player MD DeckConnecting the Antenna Terminals Connecting the supplied AM loop antennaMultiroom Setup Select the AMP mode on the remote controlOn Screen Display Menu System Speaker Setup LargeSmall YESPreference Surround PL II PRO Logic II Music ParameterCS II Circle Surround Parameter Multi RoomDC Trigger Setup CH Input LevelTo set on or OFF, press or cursor button Selecting the Surround Mode Adjusting the Tone Bass Treble ControlVideo Convert Selecting AN Input SourceSurround Mode Using the Sleep TimerTemporarily Turning OFF Sound Dolby DigitalDTS-ES Discrete 6.1, Matrix Dts, Neo6 Cinema, Neo6 MusicNeo6 Cinema, Neo6 Music SBL Other Function Recording AN Analog Source Speaker A/BCH Input HT-EQPreset Memory Using the SR7400 Using the remote control unitBasic Operation Tuner Listening to the Tuner→ B → C ... Z → 1 → 2 → 3 .... → → + → / → Blank → a ← DownMulti Room Playback Using Multi Speaker Terminals Multi Room Playback UsingMulti Room SystemRemote Controller Operation Controlling a Marantz VCR VCR ModeControlling Marantz Components Turns the CD recorder on and off When operating non-Marantz AV equipment products This example shows how to set a DVD playerBasic Operation Normal operation statusThis remote control is capable of learning Storing codes used by other remote controls thatControl will transmit either the Marantz preset Codes from the initial settings, or remote codesErasing buttons Erasing direct buttonsProgramming Macros Press the 5 numeric button to select M Press Cursor button to nextSpace Or cursor buttons to move toClone Mode Receiving remote controlTransmitting remote control Setup MoreInterval time Troubleshooting Symptom Cause RemedyMemory backup General MalfunctionTechnical Specifications Dimensions Setup Codes Tape Deck Iii VCR DVD Functions R E C T B U T T O NIs a registered trademark
Related manuals
Manual 52 pages 11.83 Kb

SR7400 specifications

The Marantz SR7400 is a distinguished audio receiver designed to provide an excellent home theater experience. Launched in the early 2000s, the SR7400 has maintained its reputation as a premium choice for audiophiles and home cinema enthusiasts due to its robust build and extensive feature set.

One of the main highlights of the SR7400 is its 7.1-channel amplification, capable of delivering a powerful and engaging sound experience. Rated at 90 watts per channel, it ensures ample output for most home environments, making it suitable for both movies and music alike. The receiver supports a variety of surround sound formats, including Dolby Digital, DTS, and Pro Logic II, enabling users to enjoy dynamic audio from their favorite media.

The SR7400 is equipped with advanced circuitry, including Marantz's proprietary HDAM (Hyper Dynamic Amplification Module) technology. This innovation enhances audio performance by minimizing distortion and improving signal clarity. The design emphasizes a high current capability, providing a lively and detailed sound stage, essential for engrossing home theater experiences.

Another significant feature is the SR7400's multi-room capability, allowing different audio sources to be played in separate zones of the house. This flexibility makes it ideal for larger homes where the desire for sound in multiple rooms is a common preference.

In terms of connectivity, the receiver boasts a comprehensive array of inputs and outputs, including multiple HDMI inputs, digital coaxial and optical connections, as well as traditional analog inputs. This versatility allows for seamless integration with various audio and video components, such as DVD players, gaming consoles, and streaming devices.

Additionally, the SR7400 supports the Audyssey MultEQ, an automatic calibration system that optimizes the audio settings based on the room's acoustics. This feature ensures that listeners experience balanced sound regardless of their positioning within the space.

In conclusion, the Marantz SR7400 combines cutting-edge technology with user-friendly features, making it a remarkable choice for anyone looking to enhance their home audio experience. With its powerful amplification, advanced audio processing capabilities, and versatile connectivity options, it remains a sought-after receiver for a truly immersive sound experience.
Top Page Image Contents