Marantz SR5000 Location and Function of Parts and Controls, Rear panel connections, AC Outlet

Page 7

LOCATION AND FUNCTION OF PARTS AND CONTROLS

ENGLISH

Rear panel connections

(See pages 108 )

All connections to the rear panel should be made with entire power off to the system. To avoid miss-connection, it is advisable to connect one cable at a time between the different components. This is the safest way to avoid cross-connecting channels or mix-up signal inputs with outputs.

AFM antenna terminal (75 ohm or 300 ohm)

For connecting an external FM antenna with a coaxial cable, or for connecting a cable network.

AM antenna and ground terminals

For connecting the supplied AM loop antenna. Use the terminals marked “AM” and “GND”.

The supplied AM loop antenna will provide good AM reception in most areas. Position the loop antenna to the best reception.

BVCR1 video input/output jacks

Connect the IN jack to your main VCR’s video output jack and connect the OUT jack to the VCR’s video input jack.

CLD/TV video input jack

Connect to a laser disc player’s video output or TV's output jack.

DDVD video input jack

Connect to a DVD's video output.

ETV MONITOR OUT jack

Connect to a TV’s video input jack.

FREMOTE jacks

Connect to other Marantz components equipped with REMOTE jacks. (See page 8.)

Marantz components utilize the Philips RC-5 remote control system language.

GTAPE 1 input jacks

Connect the output (PLAY) jack of the cassette deck to the IN jack.

HTAPE 2 input jacks

Connect the output (PLAY) jack of the cassette deck to the IN jack.

ICD input jacks

Connect to the audio output jacks of a CD player.

JVCR1 audio input/output jacks

Connect the IN jacks to a VCR’s audio output jacks and the OUT jacks to the VCR’s audio input jacks.

KDVD audio input jacks

Connect the IN jacks to a VCR's/DVD's audio output jacks.

LLD/TV audio input jacks

Connect to the audio output jacks of a laser disc player or TV.

MPRE OUT (FRONT, CENTER AND REAR JACKS)

These jacks supply pre-amp output signals, and are used for connection to external power amplifiers (if necessary).

NSURROUND speaker output terminals Connect to the surround (rear) speakers.

OCENTER speaker output terminals Connect to the center speaker.

PFRONT speaker output terminals Connect to the front speakers.

QAC OUTLET

Connect the AC power cables of a CD player, cassette deck, etc., of your system. The power supply from switched outlet is interlocked with the POWER switch of the unit. The maximum total power consumption of the connected components must not exceed the following limit:

100 W MAX.

RAC power cord

Plug into AC 230V household outlet.

SCOAX. input terminal

Connect the COAX. output jack of the (digital equipment) Player to the IN jack.

OPT. input terminal

Connect the OPT. output jack of the (digital equipment) Player to the IN jack.

IMPORTANT NOTE:

These input jacks are for DTS, AC-3 / PCM digital signals only. Do not connect standard audio outputs to these DTS, AC-3 / PCM digital input jacks.

T6ch direct in

Connect the output jack of the surround processor (e.g. Marantz DP870 etc.) to the IN jack.

Note on loudspeaker impedance:

The power ratings specified for this Marantz receiver are obtained using fixed value test load impedances. However, the actual impedance of a loudspeaker system will vary with frequency, deviating from the nominal rating. This Marantz amplifier will drive any modern loudspeaker system with a rated impedance of 8 ohms or higher. A few newer loudspeakers feature impedances of less than 8 ohms. The high current output capability of this Marantz receiver can provide the additional power necessary to drive such low impedance speakers. However, during extended passages of high volume, the protection circuitry may temporarily interrupt opera- tion. If this occurs, simply reduce the volume accordingly. The protection circuitry is specially designed so that it cannot affect the sound quality during normal operation.

6

Image 7
Contents Model SR5000 User Guide English Contents List Introduction InstallationPrecautions SR5000 FeaturesDolby PRO-LOGIC Surround Using the Surround ModesCenter Speaker Options AC Outlet Location and Function of Parts and ControlsRear panel connections PRE OUT FRONT, Center and Rear Jacks7MASTER Volume Control Front panel features5REMOTE Sensor RDS Functions Europe version only Remote control bus connectionsPlayback Operation Presetting StationsAdjustments Basic OperationÚ0DISPLAY Remote Control OperationRemote control is applicable to components that Use the RC-5 remote control cord languageOther button Surround Level buttonÚ3DIGITAL Select buttons Ú4MID Night buttonProtection Circuit Operation of Remote ControlMemory backup RepairsProblem Possible Cause Remedy Troubleshooting GuideAustria Is a registered trademark