Jonsered CC2036 manual Fuel Handling, Fuel safety

Page 18

FUEL HANDLING

Fuel safety

Never start the machine:

1If you have spilled fuel on it. Wipe off the spillage and allow remaining fuel to evaporate.

2If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water.

3If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.

Transport and storage

•Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or naked flames, for example, from electrical machinery, electric motors, electrical relays/ switches or boilers.

•When storing and transporting fuel always use approved containers intended for this purpose.

•When storing the machine for long periods the fuel tank must be emptied. Contact your local gas station to find out where to dispose of excess fuel.

•Ensure the machine is cleaned and that a complete service is carried out before long-term storage.

•The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage.

WARNING! Take care when handling fuel.

! Bear in mind the risk of fire, explosion and inhaling fumes.

Fuel

CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture.

WARNING! Fuel and fuel fumes are

! highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin. For this reason observe caution when handling fuel and make sure there is adequate ventilation.

Gasoline

CAUTION! Always use a quality gasoline/oil mixture with an octane rating of at least 87 octane ((RON+MON)/2). If your machine is equipped with a catalytic converter (see chapter on Technical data) always use a good quality unleaded gasoline/oil mixture. Leaded gasoline will destroy the catalytic converter.

Use low-emission gasoline, also known as alkylate gasoline, if it is available.

This engine is certified to operate on unleaded gasoline.

•The lowest recommended octane grade is 87 ((RON+MON)/2). If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage.

•When working at continuous high revs a higher octane rating is recommended.

Two-stroke oil

•For best results and performance use JONSERED two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines.

•Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW).

•Never use oil intended for four-stroke engines.

•Mixing ratio

1:50 (2%) with JONSERED two-stroke oil.

Gasoline, litre

Two-stroke oil, litre

 

2% (1:50)

 

 

 

5

0,10

 

 

10

0,20

 

 

15

0,30

 

 

20

0,40

 

 

US gallon

US fl. oz.

 

 

1

2 1/2

 

 

2 1/2

6 1/2

 

 

5

12 7/8

 

 

18 – English

Page 17 Page 19
Image 18
Page 17 Page 19
Contents GR2036 Operator of the machine must Ensure, while working, that no KEY to SymbolsSymbols Persons or animals come closer thanContents Introduction Dear customerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutVibration damping system Stop switchCutting attachment guard Quick releaseMuffler Locking nutCutting equipment Cutting equipmentGeneral rules Sharpening grass cutters and grass blades Sharpening the saw bladeTrimmer head Assembly Fitting the handlebarTransport position, handlebar Fitting blades and trimmer heads Fitting a blade guard, grass blade and grass cutterFitting the blade guard and saw blade Fitting the trimmer guard and trimmer head Trimmy SII AM LAdjusting the harness and clearing saw Fitting other guards and cutting attachmentsSpreading the load on your shoulders Forestry clearing Correct heightCorrect balance Grass clearingFuel safety Fuel HandlingFuel Fueling MixingStarting and stopping Starting and StoppingCheck before starting Cold engineFor throttle handles with a start throttle lock Warm engineStarting StoppingBasic safety rules Working TechniquesGeneral working instructions ABC of clearing Forestry clearing using a saw blade Grass trimming with a trimmer head Grass clearing using a grass bladeBrush cutting with a saw blade TrimmingCutting SweepingMaintenance CarburetorAdjusting the start throttle speed Fine adjustment of the idle speed TCorrectly adjusted carburetor Low speed jet LMuffler Cooling systemRemember the risk of fire Air filter Cleaning the air filterBevel gear Spark plugMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApproved accessories Type Cutting attachment guard, Art. no Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Control Warranty Parts List Poly Trim Tap n’ Go 35 Spin Tap n’Go 45 Spin Trimmy SII Page Page Page Page 1151201-95

CC2036 specifications

The Jonsered CC2036 is a powerful and efficient chainsaw designed for both professional users and homeowners looking to tackle demanding cutting tasks. Equipped with a robust 36cc engine, the CC2036 offers an impressive balance between performance and ease of use. This model is particularly favored for its lightweight design, making it an ideal choice for extended operational periods without causing fatigue.

One of the standout features of the Jonsered CC2036 is its Easy Start technology. This innovative system significantly reduces the effort required to start the engine. With just a few simple pulls, users can get the chainsaw running smoothly, making it accessible for operators of all skill levels. This technology is especially beneficial for those who may struggle with traditional starting methods.

Additionally, the CC2036 incorporates a tool-less chain tensioning system, which allows users to adjust the chain tension quickly and efficiently without the need for additional tools. This feature enhances convenience, ensuring that the chainsaw is always in optimal working condition, which is crucial for safety and performance during cutting tasks.

Another notable characteristic of the Jonsered CC2036 is its low-vibration design. This feature minimizes user fatigue and enhances comfort during prolonged use, making it suitable for tasks that require precision and stamina. The anti-vibration technology reduces the shock transmitted to the user’s hands, allowing for a more controlled and stable cutting experience.

In terms of safety, the CC2036 is equipped with a chain brake that provides instant stopping of the chain in the event of kickback, offering peace of mind to the operator. Furthermore, the chainsaw is designed with an ergonomic handle that provides a secure grip, enhancing control and maneuverability.

Fuel efficiency is another highlight of the Jonsered CC2036. Its advanced engine technology not only delivers powerful performance but also ensures lower emissions, making it an environmentally friendly choice. This blend of efficiency and power ensures that users can operate the chainsaw for extended periods without frequent refueling.

Overall, the Jonsered CC2036 is engineered for reliability and performance, making it a versatile tool for a variety of cutting applications, whether for landscaping, firewood processing, or tree maintenance. With its user-friendly features, safety mechanisms, and powerful engine, the CC2036 stands out as an excellent option for those seeking a dependable chainsaw.
Top Page Image Contents