Jonsered CC2036 manual Low speed jet L, Fine adjustment of the idle speed T, High speed jet H

Page 28

MAINTENANCE

Low speed jet L

Try to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/4 turn counter-clockwise.

+ 1/4

L

CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti-clockwise until the cutting attachment stops.

Fine adjustment of the idle speed T

Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust. First turn the idle adjustment screw T clockwise until the cutting attachment starts to rotate. Then turn the screw anticlockwise until the cutting attachment stops. The idle speed is correctly adjusted when the engine will run smoothly in every position. The idle speed should also be well below the speed at which the cutting attachment starts to rotate.

WARNING! If the idle speed cannot be

! adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired.

High speed jet H

The high speed jet H affects the engine power, speed, temperature and fuel consumption. If the high speed jet H is set too lean (screwed in too far) the engine speed will be too high and cause engine damage. Do not let the engine run at full speed for more than 10 seconds.

Note that the engine should not be under load when you adjust the high speed jet H. You should therefore remove the cutting attachment, nut, support flange and drive disc before adjusting the high speed jet H.

Apply full throttle and turn the high speed jet H very slowly clockwise until the engine slows down. Then turn the high speed jet H very slowly anticlockwise until the engine starts to run unevenly. Now turn the high speed jet H slowly clockwise a little way until the engine runs smoothly.

H

CAUTION! For optimum adjustment of the carburettor, contact a qualified dealer/service workshop that has a revolution counter at their disposal.

Correctly adjusted carburetor

When the carburetor is correctly adjusted the machine will accelerate without hesitation and burble a little at maximum speed. It is also important that the cutting attachment does not rotate at idle. If the low speed jet L is set too lean it may cause starting difficulties and poor acceleration.

If the high speed jet H is set too lean it will result in less power, less performance, poor acceleration and/or damage to the engine.

If both the L and H jets are set too rich it will results in acceleration problems or too low a working speed.

Adjusting the start throttle speed

The correct start throttle speed is set by means of an adjuster on the rear of the handle next to the cable. Use

28 – English

Page 27 Page 29
Image 28
Page 27 Page 29
Contents GR2036 KEY to Symbols SymbolsOperator of the machine must Ensure, while working, that no Persons or animals come closer thanContents Introduction Dear customerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutStop switch Cutting attachment guardVibration damping system Quick releaseMuffler Locking nutCutting equipment Cutting equipmentGeneral rules Sharpening grass cutters and grass blades Sharpening the saw bladeTrimmer head Fitting the handlebar AssemblyTransport position, handlebar Fitting a blade guard, grass blade and grass cutter Fitting blades and trimmer headsFitting the blade guard and saw blade Fitting the trimmer guard and trimmer head Trimmy SII AM LFitting other guards and cutting attachments Adjusting the harness and clearing sawSpreading the load on your shoulders Correct height Correct balanceForestry clearing Grass clearingFuel Handling Fuel safetyFuel Fueling MixingStarting and Stopping Check before startingStarting and stopping Cold engineWarm engine StartingFor throttle handles with a start throttle lock StoppingWorking Techniques Basic safety rulesGeneral working instructions ABC of clearing Forestry clearing using a saw blade Grass clearing using a grass blade Brush cutting with a saw bladeGrass trimming with a trimmer head TrimmingCutting SweepingMaintenance CarburetorFine adjustment of the idle speed T Correctly adjusted carburetorAdjusting the start throttle speed Low speed jet LCooling system MufflerRemember the risk of fire Cleaning the air filter Bevel gearAir filter Spark plugMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApproved accessories Type Cutting attachment guard, Art. no Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsEmission Control Warranty Parts List Poly Trim Tap n’ Go 35 Spin Tap n’Go 45 Spin Trimmy SII Page Page Page Page 1151201-95

CC2036 specifications

The Jonsered CC2036 is a powerful and efficient chainsaw designed for both professional users and homeowners looking to tackle demanding cutting tasks. Equipped with a robust 36cc engine, the CC2036 offers an impressive balance between performance and ease of use. This model is particularly favored for its lightweight design, making it an ideal choice for extended operational periods without causing fatigue.

One of the standout features of the Jonsered CC2036 is its Easy Start technology. This innovative system significantly reduces the effort required to start the engine. With just a few simple pulls, users can get the chainsaw running smoothly, making it accessible for operators of all skill levels. This technology is especially beneficial for those who may struggle with traditional starting methods.

Additionally, the CC2036 incorporates a tool-less chain tensioning system, which allows users to adjust the chain tension quickly and efficiently without the need for additional tools. This feature enhances convenience, ensuring that the chainsaw is always in optimal working condition, which is crucial for safety and performance during cutting tasks.

Another notable characteristic of the Jonsered CC2036 is its low-vibration design. This feature minimizes user fatigue and enhances comfort during prolonged use, making it suitable for tasks that require precision and stamina. The anti-vibration technology reduces the shock transmitted to the user’s hands, allowing for a more controlled and stable cutting experience.

In terms of safety, the CC2036 is equipped with a chain brake that provides instant stopping of the chain in the event of kickback, offering peace of mind to the operator. Furthermore, the chainsaw is designed with an ergonomic handle that provides a secure grip, enhancing control and maneuverability.

Fuel efficiency is another highlight of the Jonsered CC2036. Its advanced engine technology not only delivers powerful performance but also ensures lower emissions, making it an environmentally friendly choice. This blend of efficiency and power ensures that users can operate the chainsaw for extended periods without frequent refueling.

Overall, the Jonsered CC2036 is engineered for reliability and performance, making it a versatile tool for a variety of cutting applications, whether for landscaping, firewood processing, or tree maintenance. With its user-friendly features, safety mechanisms, and powerful engine, the CC2036 stands out as an excellent option for those seeking a dependable chainsaw.
Top Page Image Contents