Jonsered LT2119A manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate assembly and mower brackets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

Engage belt tension rod by pushing rod into locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 20 and 21)

Raise mower to its highest position.

Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

Recheck measurements after adjusting.

BOTTOM

BOTTOM EDGE

EDGE OF

OF MOWER TO

MOWER TO

GROUND

GROUND

AA

GROUND LINE

FIG. 20

SUSPENSION

ARM

LIFT LINK

ADJUSTMENT NUT

FRONT-TO-BACK ADJUSTMENT (See Figs. 22 and 23)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

Before making any necessary adjustments, check that both front plate links are equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns. The two front links must remain equal in length.

When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

Recheck side-to-side adjustment.

BLADE

“B”“B”

FIG. 22

BOTH FRONT PLATE LINKS MUST BE

 

EQUAL IN LENGTH

NUT “D”

NUT “C”

FRONT PLATE

TRUNNION

 

ASSEMBLY

 

FIG. 21

FIG. 23

21

 

Image 21
Contents Model NO. LT2119A JNA19H48B Safety Rules Safety Rules Table of Contents Steering Wheel Gauge Wheels Unassembled PartsTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Clean AIR INTAKE/COOLING Areas CleaningMuffler Spark PlugsService and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Drive Belt To Check and Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Throttle Control Cable See Fig To Remove Hood and Grill Assembly See FigTo Adjust Choke Control See Fig To Adjust CarburetorOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsOFF Tractor Model NO. LT2119A JNA19H48B, Product no 13 SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures Repair Parts Tractor Model NO. LT2119A JNA19H48B, Product no 13 Drive Steering Assembly Repair Parts Seat Assembly Wheels & Tires DecalsEngine KEY Part NO. NO. Description Mower Deck Repair Parts Mower Lift Repair Parts Service Notes Suggested Guide for Sighting Slopes for Safe Operation Jonsered

LT2119A specifications

The Jonsered LT2119A is a robust and efficient lawn tractor, designed to cater to the needs of homeowners seeking a reliable solution for their mowing and gardening tasks. With an emphasis on performance, comfort, and user-friendliness, the LT2119A showcases a blend of innovative engineering and practical features that make it ideal for various lawn conditions.

One of the standout features of the LT2119A is its powerful 19 horsepower Briggs & Stratton engine. This four-stroke engine ensures smooth operation while delivering sufficient power to tackle both small and large lawns. The engine's design emphasizes fuel efficiency and low emissions, aligning with modern environmental standards and reducing the overall cost of operation.

The LT2119A comes equipped with a 97 cm (approximately 38 inches) cutting deck that enables users to cover substantial ground in a single pass. The cutting height is easily adjustable, allowing for a customized mowing experience based on the specific conditions of the lawn. This versatility ensures that the tractor delivers a clean and even cut, regardless of grass type or height.

Another notable characteristic of the LT2119A is its superior maneuverability. The tractor is designed with a tight turning radius, allowing users to navigate around obstacles and tight spaces effortlessly. This feature optimizes efficiency, especially in intricate garden layouts or when mowing around trees and flower beds.

The ergonomic design of the LT2119A enhances user comfort during operation. It features a comfortable seat with a high backrest, which provides adequate support for longer mowing sessions. The steering wheel is positioned to ensure a relaxed grip, reducing strain on the arms and shoulders. Additionally, the simple control layout allows for intuitive operation, making it accessible for users of all experience levels.

The tractor also incorporates advanced technologies for enhanced functionality. The electric start system eliminates the hassle of pull cords, making it easier to start the engine with just the push of a button. The LT2119A is also equipped with a cutting blade engagement system that ensures quick and efficient blade operation.

In summary, the Jonsered LT2119A is a well-rounded lawn tractor that combines power, efficiency, and ease of use. With its strong engine, adjustable cutting deck, and comfortable design, it stands out as a reliable choice for homeowners looking to maintain their lawns effectively. Whether you're tackling overgrown grass or simply performing regular maintenance, the LT2119A provides the performance and features necessary for successful lawn care.