Jonsered LT2119A manual To Replace Motion Drive Belt See Fig, Transmission REMOVAL/REPLACEMENT

Page 23

SERVICE AND ADJUSTMENTS

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress brake pedal all the way down and engage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-3/4", loosen jam nut and turn nut “A” until distance becomes 1-3/4". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

1-3/4"

NUT “A”

JAM NUT

OPERATING

ARM

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUSTMENT IS NECESSARY CONTACT YOUR NEAREST AUTHORIZED SER- VICE CENTER/DEPARTMENT

FIG. 26

TO REPLACE MOTION DRIVE BELT (See Fig. 27)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

•Remove mower (See “TO REMOVE MOWER” in this section of this manual.)

•Disconnect clutch wire harness.

•Remove clutch locator.

•Remove belt from stationary idler and clutching idler.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Pull belt toward front of tractor and remove downwards from around electric clutch.

•Install new belt by reversing above procedure.

ELECTRIC

CLUTCH LOCATOR

CLUTCH

 

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEYCLUTCH WIRE HARNESS

FIG. 27

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model NO. LT2119A JNA19H48B Safety Rules Safety Rules Table of Contents Steering Wheel Gauge Wheels Unassembled PartsTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Brake System Check Tire PressureCheck Mower Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelAutomatic Transmission Warm UP Purge TransmissionMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Spark Plugs CleaningClean AIR INTAKE/COOLING Areas MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Check Brake To Check and Adjust Brake See FigTo Replace Mower Drive Belt To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive Belt See FigInterlocks and Relays To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Replace Headlight BulbTo Adjust Carburetor To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig To Adjust Choke Control See FigEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsOFF Tractor Model NO. LT2119A JNA19H48B, Product no 13 SchematicElectrical KEY Part NO. NO. Description Chassis and Enclosures Repair Parts Tractor Model NO. LT2119A JNA19H48B, Product no 13 Drive Steering Assembly Repair Parts Seat Assembly Wheels & Tires DecalsEngine KEY Part NO. NO. Description Mower Deck Repair Parts Mower Lift Repair Parts Service Notes Suggested Guide for Sighting Slopes for Safe Operation Jonsered

LT2119A specifications

The Jonsered LT2119A is a robust and efficient lawn tractor, designed to cater to the needs of homeowners seeking a reliable solution for their mowing and gardening tasks. With an emphasis on performance, comfort, and user-friendliness, the LT2119A showcases a blend of innovative engineering and practical features that make it ideal for various lawn conditions.

One of the standout features of the LT2119A is its powerful 19 horsepower Briggs & Stratton engine. This four-stroke engine ensures smooth operation while delivering sufficient power to tackle both small and large lawns. The engine's design emphasizes fuel efficiency and low emissions, aligning with modern environmental standards and reducing the overall cost of operation.

The LT2119A comes equipped with a 97 cm (approximately 38 inches) cutting deck that enables users to cover substantial ground in a single pass. The cutting height is easily adjustable, allowing for a customized mowing experience based on the specific conditions of the lawn. This versatility ensures that the tractor delivers a clean and even cut, regardless of grass type or height.

Another notable characteristic of the LT2119A is its superior maneuverability. The tractor is designed with a tight turning radius, allowing users to navigate around obstacles and tight spaces effortlessly. This feature optimizes efficiency, especially in intricate garden layouts or when mowing around trees and flower beds.

The ergonomic design of the LT2119A enhances user comfort during operation. It features a comfortable seat with a high backrest, which provides adequate support for longer mowing sessions. The steering wheel is positioned to ensure a relaxed grip, reducing strain on the arms and shoulders. Additionally, the simple control layout allows for intuitive operation, making it accessible for users of all experience levels.

The tractor also incorporates advanced technologies for enhanced functionality. The electric start system eliminates the hassle of pull cords, making it easier to start the engine with just the push of a button. The LT2119A is also equipped with a cutting blade engagement system that ensures quick and efficient blade operation.

In summary, the Jonsered LT2119A is a well-rounded lawn tractor that combines power, efficiency, and ease of use. With its strong engine, adjustable cutting deck, and comfortable design, it stands out as a reliable choice for homeowners looking to maintain their lawns effectively. Whether you're tackling overgrown grass or simply performing regular maintenance, the LT2119A provides the performance and features necessary for successful lawn care.
Top Page Image Contents