Jonsered LT2119A manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping pur- poses. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

3/4" wrench

Utility knife

(1)

7/16" wrench

Tire pressure gauge

(1)

3/4" socket with drive ratchet

Pliers

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton .

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Remove mower and packing materials.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

STEERING WHEEL

STEERING BOOT

STEERING

WHEEL EXTENTION SHAFT

STEERING

SHAFT

STEERING WHEEL INSERT

LOCK NUT

LARGE FLAT WASHER

TABS

STEERING WHEEL ADAPTOR

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten se- curely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

FIG. 1

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

•Lift hood to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in MAINTENANCE section of this manual for charging instructions).

LABEL

FIG. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. LT2119A JNA19H48B Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel Gauge WheelsHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceLubrication Chart Before Each USETractor Engine Muffler CleaningClean AIR INTAKE/COOLING Areas Spark PlugsService and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Replace Mower Drive Belt To Check BrakeTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Fig Interlocks and RelaysTo Adjust Choke Control See Fig To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable See Fig To Adjust CarburetorFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionOFF Schematic Tractor Model NO. LT2119A JNA19H48B, Product no 13Electrical KEY Part NO. NO. Description Chassis and Enclosures Repair Parts Tractor Model NO. LT2119A JNA19H48B, Product no 13 Drive Steering Assembly Repair Parts Seat Assembly Decals Wheels & TiresEngine KEY Part NO. NO. Description Mower Deck Repair Parts Mower Lift Repair Parts Service Notes Suggested Guide for Sighting Slopes for Safe Operation Jonsered

LT2119A specifications

The Jonsered LT2119A is a robust and efficient lawn tractor, designed to cater to the needs of homeowners seeking a reliable solution for their mowing and gardening tasks. With an emphasis on performance, comfort, and user-friendliness, the LT2119A showcases a blend of innovative engineering and practical features that make it ideal for various lawn conditions.

One of the standout features of the LT2119A is its powerful 19 horsepower Briggs & Stratton engine. This four-stroke engine ensures smooth operation while delivering sufficient power to tackle both small and large lawns. The engine's design emphasizes fuel efficiency and low emissions, aligning with modern environmental standards and reducing the overall cost of operation.

The LT2119A comes equipped with a 97 cm (approximately 38 inches) cutting deck that enables users to cover substantial ground in a single pass. The cutting height is easily adjustable, allowing for a customized mowing experience based on the specific conditions of the lawn. This versatility ensures that the tractor delivers a clean and even cut, regardless of grass type or height.

Another notable characteristic of the LT2119A is its superior maneuverability. The tractor is designed with a tight turning radius, allowing users to navigate around obstacles and tight spaces effortlessly. This feature optimizes efficiency, especially in intricate garden layouts or when mowing around trees and flower beds.

The ergonomic design of the LT2119A enhances user comfort during operation. It features a comfortable seat with a high backrest, which provides adequate support for longer mowing sessions. The steering wheel is positioned to ensure a relaxed grip, reducing strain on the arms and shoulders. Additionally, the simple control layout allows for intuitive operation, making it accessible for users of all experience levels.

The tractor also incorporates advanced technologies for enhanced functionality. The electric start system eliminates the hassle of pull cords, making it easier to start the engine with just the push of a button. The LT2119A is also equipped with a cutting blade engagement system that ensures quick and efficient blade operation.

In summary, the Jonsered LT2119A is a well-rounded lawn tractor that combines power, efficiency, and ease of use. With its strong engine, adjustable cutting deck, and comfortable design, it stands out as a reliable choice for homeowners looking to maintain their lawns effectively. Whether you're tackling overgrown grass or simply performing regular maintenance, the LT2119A provides the performance and features necessary for successful lawn care.
Top Page Image Contents