Basic Operation, Listening to the Tuner

BASIC OPERATION

LISTENING TO THE TUNER

MANUAL TUNING

1.To select the tuner as the source, press the TUNER button t on the front panel or press the TUNER button c on the remote.

2.Press the TUNER button t on the front panel or press the TUNER button c on the remote to select the desired frequency band if required.

3.Press the F/P button !5on the front panel to display the frequency.

4.Press the TUNING/PRESET or button !4on the front panel or press the 1or ¡button ⁄2on the remote.

5.If FM is selected, press the MODE button !6on the front panel or press the MODE button ⁄2on the remote control to select the desired audio mode.

(FM) MODE BUTTON OPERATION

When “AUTO” indicator is on in the display, FM stations that broadcast in stereo will be received in stereo and the “STEREO” indicator lights.

When “AUTO” indicator is off, all the FM stations will be received in mono regardless of whether or not they are broadcasting in stereo.

AUTO TUNING (USING THE SR5200)

1.Press the F/P button !5on the front panel to display the frequency.

2.Press the TUNING/PRESET or button !4on the front panel for more than 1 second to start the Auto tuning function.

AUTO TUNING (USING THE REMOTE CONTROL UNIT)

Press 1 or ¡ button ⁄2for more than 1 second to start the Auto tuning function.

PRESET TUNING

With this unit you can preset up to 30 FM/AM stations in any order. For each station, you can memorize the frequency and reception mode if desired.

1-a. Manual Presetting (Using the SR5200)

1.Refer to the “MANUAL TUNING” or “AUTO TUNING” section above to tune in a desired station.

2.Press the MEMORY button !3. “MEMORY” indicator starts blinking on the display.

While “MEMORY” is still blinking (approx. 5 seconds), select the

preset number by pressing the TUNING/PRESET or button !4 then press the MEMORY button !3again.

3.When a number has been properly input, “MEMORY” indicator stops blinking and goes out.

The station is now stored in the specified preset memory location.

1-b. Manual Presetting (Using the remote control unit)

1.Tune in a desired station.

2.Press the MEMO button ⁄6.

3.Enter the desired preset number with ten keypad ..

4.Then, press MEMO button ⁄6again to store.

2.Auto Presetting

This function automatically scans the AM and FM band and enters all stations with sufficient signal strength into the memory.

1.Press and hold down the MEMORY button !3and TUNER button t simultaneously, auto presetting will start.

2.“MEMORY“ will blink on the display.

3.Each time the tuner finds a station, the scanning will pause and memory. Auto presetting will starts.

4.Operation stops automatically when all 30 preset memory positions are filled or when auto scanning attains the highest end of all bands.

To stop the auto preset function at anytime, press the CLEAR button !2.

3.Recalling a Preset Station

1.Press the F/P button !5to change the display to preset.

2.Select the desired preset station by pressing TUNING/PRESET or button !4on the front panel or press CHANNEL button ⁄2 on the remote.

Note:

To directly access the preset stations using the numeric keypad, select the desired preset station by entering one or two digits using the numeric keypad ..

To return to the Manual Tuning mode, press the F/P button !5.

4.Preset Scan Tuning (Using the remote control unit)

1.Press the P.SCAN button ⁄0on the remote control. (The preset station with the smallest preset number is recalled first. If no stations have been preset, “NO PRESET” shows in the display and the unit returns to the previous mode.)

2.Preset stations are recalled in sequence (CH-1 → CH-2, etc.) for 5 seconds each. Preset numbers that do not contain stations are skipped.

3.You can fast forward the preset stations by pressing the CHANNEL ¢button ⁄2continuously.

When the desired preset station is received, cancel the preset scan operation by pressing the CHANNEL 4button ⁄2or the CLEAR button ⁄7.

5.Clearing Preset Stations

You can remove preset stations from memory using the following procedure.

1.Recall the preset number to be cleared with the method described in “Recalling” a preset station .

2.Press the CLEAR button !2on the front panel or CLEAR button

⁄7on the remote control unit for 3 seconds or more.

“CLEAR” appears on the display to indicate that the specified preset number has been cleared.

6.Frequency Direct Call

1.Press F.DIRECT button ⁄2in the TUNER mode on the remote controller.

2.Display shows “ FM– – –.– –MHz” (at FM mode).

3.Input your desired frequency with tenkeypad buttons on the remote controller.

Eg) 98.1 MHz

Press 9, 8, 1 and 0

4.Press the F.DIRECT button ⁄2again.

ENGLISH