Jonsered cs 2159 manual Tensioning the chain, General advice on setting raker clearance

Page 13

SAFETY INSTRUCTIONS

C General advice on setting raker clearance

•When you sharpen the cutting teeth you reduce the

RAKER CLEARANCE (cutting depth). To maintain cutting performance you must file back the raker teeth to the recommended height.

See the ”Technical data” section to find the raker clearance for your saw chain.

•On a low-kickback cutting link the front edge of the raker lip is rounded. It is very important that you maintain this radius or bevel when you adjust the raker clearance.

•We recommend the use of a

raker gauge to achieve the correct clearance and bevel on the raker lip.

The risk of kickback is increased if the raker clearance is too large!

DSetting the raker clearance

•Before setting the raker clearance the cutting teeth should be newly sharpened.

We recommend that you adjust the raker clearance every third time you sharpen the chain. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

• To adjust the raker clearance you will need a FLAT FILE and a RAKER GAUGE.

• Place the gauge over the raker lip.

•Place the file over the part of the lip that protrudes through the gauge and file

off the excess. The clearance is correct when you no longer feel any resistance as you draw the file over the gauge.

3 Tensioning the chain

A slack chain may jump off and cause serious or even fatal injury.

•The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

•Check the chain tension every time you refuel.

NOTE! A new saw chain has a running-in period during which you should check the tension more frequently.

•Tension the chain as tightly as possible, but not so tight that you cannot pull it round

freely by hand.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents EPA Operator´s manualSymbols KEY to SymbolsContents Personal Protective Equipment Safety Instructions3a Starting Chain brake and front hand guardChain catcher Throttle lockRight hand guard Vibration damping system Stop switchMuffler Checking the front hand guard Checking brake band wearChecking the inertia brake release Checking the brake triggerThrottle lock 5 basic rules Cutting EquipmentBar Cutting equipment designed to minimise kickbackSaw chain Some terms that describe the bar and chainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth Risk of kickback is increased with a badly sharpened chainSetting the raker clearance General advice on setting raker clearanceTensioning the chain Chain oil Lubricating cutting equipmentFilling with chain oil Never use waste oilChecking chain lubrication Needle bearing maintenanceChecking wear on cutting equipment Lubricating the bar tip sprocketWhat is kickback? HOW to Avoid KickbackDo not let go of the handles General rulesNever use the saw one- handed 10 ft Min mGeneral Working Instructions Basic safety rulesGeneral Basic cutting techniqueTerms CuttingSafe distance Tree felling techniqueLimbing Felling directionFelling Clearing the trunk and preparing your retreatFreeing a tree that has fallen badly = high accident risk General adviceCutting the trunk into logs Freeing a Trapped treeWhat is what? What is WHAT?Mounting guide bar and chain AssemblyFuelmix Fuel HandlingChain oil FuellingMin 3 m 10ftStart and stop Start and StopStart StopCarburetor MaintenanceStarter device Starter device assemblyChanging a broken or worn starter cord Tensioning the recoil springAir filter Needle bearing maintenance Spark plugMuffler IMPORTANT! a damaged air filter must always be replacedCentrifugal cleaning Adjustment of the oil pump Heated handles CS 2159 WCooling system Winter useMonthly maintenance Weekly maintenance Daily maintenanceTechnical Data + 46 36 14 65 00. Warranty Period Emission Control Warranty Statement+ 46 36 14 65 2002W43 108 88
Top Page Image Contents