Jonsered CS 2152 EPA III manual Spark plug, Needle bearing lubrication, Adjustment of the oil pump

Page 35

MAINTENANCE

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter

must always be replaced.

A JONSERED chain saw can be equipped with different types of air filter according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburetor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

Needle bearing lubrication

The clutch drum has a needle bearing on the output shaft. This needle bearing must be lubricated regularly (once a week). CAUTION! Use only high quality bearing grease or engine oil. See instructions under the heading Cutting equipment.

Adjustment of the oil pump

The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The machine is supplied from the factory with the screw set to position 2. Turning the screw clockwise will reduce the oil flow and turning the screw anti- clockwise will increase the oil flow.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm). The spark plug should be replaced after about a month in operation or earlier if necessary.

2 1

3

+ –

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

Lubricating the bar tip sprocket

Lubricate the bar tip sprocket each time you refuel. Use the special grease gun and a good quality bearing grease.

Recommended settings:

Bar 13"-15": Position 1

Bar 15"-18": Position 2

Bar 18"-20": Position 3

 

!

WARNING! The engine must be stopped

 

when making adjustments.

 

 

 

 

 

English – 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents CS 2152 CS Symbols in the operator’s manual KEY to SymbolsSymbols on the machine EPA You will find the following labels on your chain sawContents Dear customer IntroductionWhat is what on the chain saw? What is WHAT?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Vibration damping system Throttle lockoutChain catcher Right hand guardGeneral rules Stop switchCutting equipment MufflerChain Cutting equipment designed to reduce kickbackBar General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingTensioning the chain Checking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Working with the chain AssemblyFitting the bar and chain Fuel Fuel HandlingLong-term storage Fuel safetyFueling Transport and storageWarm engine Starting and StoppingStarting and stopping Cold engineStopping General working instructions Basic safety rulesWorking Techniques Before useGeneral rules Terms Basic cutting techniqueLimbing Clearing the trunk and preparing your retreat Tree felling techniqueSafe distance Felling directionFelling cut Directional cutsCutting trees and branches that are in tension General adviceFreeing a tree that has fallen badly Freeing a trapped treeCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment High speed jet H Correctly adjusted carburetorImmediately Checking the brake triggerChanging a broken or worn starter cord MufflerStarter Fitting the starter Air filterTensioning the recoil spring Changing a broken recoil springLubricating the bar tip sprocket Adjustment of the oil pumpSpark plug Needle bearing lubricationWinter use Air Injection centrifugal cleaningTemperature 0C 32F or colder Cooling systemElectrical carburetor heating Heated handlesDaily maintenance Weekly maintenance Monthly maintenance Maintenance scheduleTechnical data Technical Data058/1,5 mm Bar and chain combinationsSaw chain filing and file gauges 050/1,3 mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementOther safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Kickback safety precautionsPage 1151441-95

CS 2152 EPA III, CS 2153 EPA I specifications

Jonsered, a renowned name in the outdoor power tool industry, has produced a range of high-performance chainsaws designed for both professional and hobbyist use. Two noteworthy models are the Jonsered CS 2153 EPA I and the CS 2152 EPA III. Both chainsaws boast a combination of power, efficiency, and innovative technology, making them ideal for various cutting tasks.

The Jonsered CS 2153 EPA I is equipped with a robust 50cc engine that delivers an impressive power output, allowing for quick and efficient cutting through a variety of wood types. The chainsaw features a lightweight design, ensuring ease of handling and reduced fatigue during prolonged use. One of the standout features of the CS 2153 is its Rapid Reaction Start system, which significantly decreases starting effort and ensures a reliable ignition. This makes it particularly convenient for users who need to start the chainsaw multiple times throughout the day.

Additionally, the CS 2153 incorporates an ergonomic handle design, which improves comfort and control. The anti-vibration technology integrated into the saw helps to minimize the amount of vibration transferred to the user's hands, contributing to a smoother operation and less strain during long cutting sessions. Furthermore, the chainsaw comes with a tool-less chain tensioning system, allowing for quick adjustments without the need for additional tools, enhancing efficiency and saving valuable time.

On the other hand, the Jonsered CS 2152 EPA III features a slightly smaller yet powerful 40cc engine, making it an ideal choice for both light-duty and medium-duty cutting applications. Similar to the CS 2153, this model also boasts a lightweight and well-balanced design, making maneuverability easy for users. The CS 2152 is known for its exceptional fuel efficiency, thanks to the innovative X-Torq engine technology, which reduces fuel consumption and minimizes harmful emissions. This feature not only makes it environmentally friendly, but also reduces running costs over time.

Both models highlight Jonsered's commitment to user safety with a chain brake system that stops the chain in the event of kickback and a handguard to protect the user's hands. Overall, the Jonsered CS 2153 EPA I and CS 2152 EPA III are exceptional chainsaws, combining power, efficiency, and comfort in a user-friendly package. Whether you're a professional logger or a homeowner tackling occasional yard work, these chainsaws are sure to meet your cutting needs effectively and reliably.
Top Page Image Contents