Jonsered CS 2153 EPA I, CS 2152 EPA III manual Tensioning the chain

Page 14

GENERAL SAFETY PRECAUTIONS

•File all the teeth to the same length. When the length of the cutting teeth is reduced to 0.16 inch (4 mm) the chain is worn out and should be replaced.

General advice on adjusting depth gauge setting

•When you sharpen the cutting tooth (A) the depth gauge setting (C) will decrease. To maintain optimal cutting performance the depth gauge (B) has to be filed down to achieve the recommended depth gauge setting. See instructions under the heading Technical data to find the correct depth gauge setting for your particular chain.

 

!

WARNING! The risk of kickback is

 

increased if the depth gauge setting is

 

 

too large!

 

 

 

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

Tensioning the chain

WARNING! A slack chain may jump off

! the bar and cause serious or even fatal injury.

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Loosen the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

14 – English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents CS 2152 CS Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain saw EPAContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesChain Cutting equipment designed to reduce kickbackBar Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Checking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Working with the chain AssemblyFitting the bar and chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Correctly adjusted carburetor High speed jet HChecking the brake trigger ImmediatelyChanging a broken or worn starter cord MufflerStarter Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterNeedle bearing lubrication Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketCooling system Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useHeated handles Electrical carburetor heatingMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage 1151441-95

CS 2152 EPA III, CS 2153 EPA I specifications

Jonsered, a renowned name in the outdoor power tool industry, has produced a range of high-performance chainsaws designed for both professional and hobbyist use. Two noteworthy models are the Jonsered CS 2153 EPA I and the CS 2152 EPA III. Both chainsaws boast a combination of power, efficiency, and innovative technology, making them ideal for various cutting tasks.

The Jonsered CS 2153 EPA I is equipped with a robust 50cc engine that delivers an impressive power output, allowing for quick and efficient cutting through a variety of wood types. The chainsaw features a lightweight design, ensuring ease of handling and reduced fatigue during prolonged use. One of the standout features of the CS 2153 is its Rapid Reaction Start system, which significantly decreases starting effort and ensures a reliable ignition. This makes it particularly convenient for users who need to start the chainsaw multiple times throughout the day.

Additionally, the CS 2153 incorporates an ergonomic handle design, which improves comfort and control. The anti-vibration technology integrated into the saw helps to minimize the amount of vibration transferred to the user's hands, contributing to a smoother operation and less strain during long cutting sessions. Furthermore, the chainsaw comes with a tool-less chain tensioning system, allowing for quick adjustments without the need for additional tools, enhancing efficiency and saving valuable time.

On the other hand, the Jonsered CS 2152 EPA III features a slightly smaller yet powerful 40cc engine, making it an ideal choice for both light-duty and medium-duty cutting applications. Similar to the CS 2153, this model also boasts a lightweight and well-balanced design, making maneuverability easy for users. The CS 2152 is known for its exceptional fuel efficiency, thanks to the innovative X-Torq engine technology, which reduces fuel consumption and minimizes harmful emissions. This feature not only makes it environmentally friendly, but also reduces running costs over time.

Both models highlight Jonsered's commitment to user safety with a chain brake system that stops the chain in the event of kickback and a handguard to protect the user's hands. Overall, the Jonsered CS 2153 EPA I and CS 2152 EPA III are exceptional chainsaws, combining power, efficiency, and comfort in a user-friendly package. Whether you're a professional logger or a homeowner tackling occasional yard work, these chainsaws are sure to meet your cutting needs effectively and reliably.
Top Page Image Contents