Jonsered CS 2153 EPA I Air filter, Tensioning the recoil spring, Changing a broken recoil spring

Page 34

MAINTENANCE

•Pull out the cord approx. 30 cm (12 inches) and hook it into the notch in the rim of the pulley. Release the recoil spring by letting the pulley rotate slowly backwards.

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley. Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the center of the pulley. Insert the starter cord through the hole in the starter housing and the starter handle. Make a secure knot in the end of the starter cord.

Tensioning the recoil spring

•Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned an additional 1/2 turn when the starter cord is pulled all the way out.

Changing a broken recoil spring

•Lift up the starter pulley. See instructions under the heading Changing a broken or worn starter cord. Remember that the recoil spring is coiled under tension in the starter housing.

•Remove the cassette with the recoil spring from the starter.

•Lubricate the recoil spring with light oil. Fit the cassette with recoil spring in the starter. Fit the starter pulley and tension the recoil spring.

Fitting the starter

•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it.

34 – English

Page 33 Page 35
Image 34
Page 33 Page 35
Contents CS 2152 CS Symbols on the machine KEY to SymbolsSymbols in the operator’s manual You will find the following labels on your chain saw EPAContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Before using a new chain saw General Safety PrecautionsAlways use common sense Personal protective equipment Machine′s safety equipmentChain brake and front hand guard General Safety Precautions Right hand guard Throttle lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesBar Cutting equipment designed to reduce kickbackChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Filling with chain oil Lubricating cutting equipmentChecking chain lubrication Needle bearing lubrication Chain drive sprocketChecking wear on cutting equipment Fitting the bar and chain AssemblyWorking with the chain Fuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageCold engine Starting and StoppingStarting and stopping Warm engineStopping Before use Basic safety rulesWorking Techniques General working instructionsGeneral rules Basic cutting technique TermsLimbing Felling direction Tree felling techniqueSafe distance Clearing the trunk and preparing your retreatDirectional cuts Felling cutFreeing a trapped tree General adviceFreeing a tree that has fallen badly Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburetor adjustment MaintenanceGeneral Correctly adjusted carburetor High speed jet HChecking the brake trigger ImmediatelyStarter MufflerChanging a broken or worn starter cord Changing a broken recoil spring Air filterTensioning the recoil spring Fitting the starterNeedle bearing lubrication Adjustment of the oil pumpSpark plug Lubricating the bar tip sprocketCooling system Air Injection centrifugal cleaningTemperature 0C 32F or colder Winter useHeated handles Electrical carburetor heatingMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data050/1,3 mm Bar and chain combinationsSaw chain filing and file gauges 058/1,5 mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsKickback safety precautions American Standard Safety PrecautionsSafety precautions for chain saw users Other safety precautionsPage 1151441-95

CS 2152 EPA III, CS 2153 EPA I specifications

Jonsered, a renowned name in the outdoor power tool industry, has produced a range of high-performance chainsaws designed for both professional and hobbyist use. Two noteworthy models are the Jonsered CS 2153 EPA I and the CS 2152 EPA III. Both chainsaws boast a combination of power, efficiency, and innovative technology, making them ideal for various cutting tasks.

The Jonsered CS 2153 EPA I is equipped with a robust 50cc engine that delivers an impressive power output, allowing for quick and efficient cutting through a variety of wood types. The chainsaw features a lightweight design, ensuring ease of handling and reduced fatigue during prolonged use. One of the standout features of the CS 2153 is its Rapid Reaction Start system, which significantly decreases starting effort and ensures a reliable ignition. This makes it particularly convenient for users who need to start the chainsaw multiple times throughout the day.

Additionally, the CS 2153 incorporates an ergonomic handle design, which improves comfort and control. The anti-vibration technology integrated into the saw helps to minimize the amount of vibration transferred to the user's hands, contributing to a smoother operation and less strain during long cutting sessions. Furthermore, the chainsaw comes with a tool-less chain tensioning system, allowing for quick adjustments without the need for additional tools, enhancing efficiency and saving valuable time.

On the other hand, the Jonsered CS 2152 EPA III features a slightly smaller yet powerful 40cc engine, making it an ideal choice for both light-duty and medium-duty cutting applications. Similar to the CS 2153, this model also boasts a lightweight and well-balanced design, making maneuverability easy for users. The CS 2152 is known for its exceptional fuel efficiency, thanks to the innovative X-Torq engine technology, which reduces fuel consumption and minimizes harmful emissions. This feature not only makes it environmentally friendly, but also reduces running costs over time.

Both models highlight Jonsered's commitment to user safety with a chain brake system that stops the chain in the event of kickback and a handguard to protect the user's hands. Overall, the Jonsered CS 2153 EPA I and CS 2152 EPA III are exceptional chainsaws, combining power, efficiency, and comfort in a user-friendly package. Whether you're a professional logger or a homeowner tackling occasional yard work, these chainsaws are sure to meet your cutting needs effectively and reliably.
Top Page Image Contents