Jonsered 70C, 50C manual Muffler, Checking brake band wear, Checking the front hand guard

Page 8

SAFETY INSTRUCTIONS

Muffler

The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.

WARNING! The exhaust fumes from the

!engine are hot and may contain sparks which can start a fire. Never start the machine indoors or near combustible material!

In areas with a hot, dry climate there is a high risk of fires. These areas are sometimes controlled by legislation and requirements that among other things the muffler must be equipped with an approved type of spark arrestor mesh.

For mufflers it is very important that you follow the instructions on checking, maintaining and servicing your machine. See instructions under the heading Checking, maintaining and servicing the machine’s safety equipment.

WARNING! The muffler gets very hot in use

!and remains so for a short time afterwards. Do not touch the muffler if it is hot!

Checking, maintaining and servicing the machine′s safety equipment

WARNING! All servicing and repair work on

!the machine requires special training.This is especially true of the machine′s safety equipment. If your machine fails any of the checks described below you must contact your service agent. When you buy any of our products we guarantee the availability of professional repairs and service. If the retailer who sells your machine is not a servicing dealer, ask him for the address of your nearest service agent.

Chain brake and front hand guard

Checking brake band wear

Brush off any wood dust, resin and dirt from the chain brake and clutch drum. Dirt and wear can impair operation of the brake.

Regularly check that the brake band is at least 0.6 mm thick at its thinnest point.

8 – English

Checking the front hand guard

Make sure the front hand guard is not damaged and that there are no visible defects such as cracks.

Move the front hand guard forwards and back to make sure it moves freely and that it is securely anchored to the clutch cover.

Checking the inertia brake release

Hold the chain saw over a stump or other firm object. Let go of the front handle so that the bar drops towards the stump as the chain saw rotates around the rear handle.

When the bar hits the stump the brake should be applied.

Checking the brake trigger

Place the chain saw on firm ground and start it. Make sure the chain does not touch the ground or any other object. See the instructions under the heading Start and stop.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Operator’s manual EPA KEY to Symbols Key to symbolsContents EPA Personal protective equipment Safety Instructions Machine′s safety equipment Chain brake and front hand guard Stop switch Throttle lockChain catcher Right hand guardMuffler Checking brake band wearChecking the front hand guard Checking the inertia brake releaseStop switch Throttle lockChain catcher Right hand guardCutting equipment General rulesCutting equipment designed to minimise kickback MufflerSharpening your chain and adjusting raker clearance ChainSome terms that describe the bar and chain General information on sharpening cutting teethGeneral advice on setting raker clearance Sharpening cutting teethSetting the raker clearance Tensioning the chainIf the raker clearance is too large Cause serious or even fatal injuryLubricating cutting equipment How to avoid kickback What is kickback?Checking wear on cutting equipment Chain drive sprocketDo not let go of the handles General safety precautions StartingFuel safety Basic safety rulesGeneral working instructions Transport and storageTerms Basic cutting techniqueGeneral Cutting LimbingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatFelling cut General advice Freeing a tree that has fallen badlyCutting the trunk into logs Freeing a trapped treeWhat is WHAT? What is what on the chain saw?Assembly Fitting the bar and chainChain oil Fuel HandlingFuel Fuelling Starting and Stopping Starting and stoppingCold engine Warm engineStopping Maintenance CarburettorCorrectly adjusted carburettor StarterChanging a broken or worn starter cord Tensioning the recoil springAir filter Spark plugMuffler Fitting the starterAdjustment of the oil pump Centrifugal cleaning TurboWhen making adjustments Needle bearing lubricationHeated handles Electrical carburettor heatingWinter use CanadaBelow you will find some general maintenance instructions Daily maintenance Weekly maintenanceMonthly maintenance CS 2171/WH Technical DataTechnical data Bar Chain Length, inches Pitch, inch Max nose radius050/1,3 mm 058/1,5mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsPage 1088917-95

50C, 70C specifications

The Jonsered 70C and 50C chainsaws represent a pinnacle of craftsmanship and engineering excellence in the world of power tools. Designed for both professional and avid DIY enthusiasts, these models offer a blend of power, performance, and user-friendly features that elevate the cutting experience.

At the heart of both the Jonsered 70C and 50C is their powerful engine output. The 70C boasts a robust 70cc engine, delivering high torque and efficiency for demanding tasks, while the 50C is equipped with a nimble 50cc engine, perfect for lighter, more agile cutting projects. This versatility makes the chainsaws suitable for a wide range of activities, from felling trees to limbing and pruning, ensuring that they cater to varying user requirements.

One notable feature of the Jonsered 70C and 50C is their advanced air filtration systems. These systems are designed to enhance the longevity of the chainsaw's engine by preventing dust and debris from entering the combustion area. This means less maintenance and more time spent operating the chainsaw, making it an ideal choice for both professional lumberjacks and casual users.

Ergonomically designed, the handle of both models offers excellent grip and comfort, reducing user fatigue during extended use. The lightweight construction of the saws enables effortless maneuverability and control, allowing users to execute precise cuts without strain. Additionally, the quick and easy chain tensioning system facilitates fast adjustments, ensuring that the chain remains in optimal condition for continuous cutting.

Safety features are paramount in the design of the Jonsered 70C and 50C. Each model incorporates a chain brake and throttle lock to enhance user safety while operating, minimizing risks associated with kickback and accidental starts. The designs also emphasize low vibration, which further protects the user's hands and arms from fatigue, promoting a safer and more enjoyable cutting experience.

With their blend of power, efficiency, and advanced technology, the Jonsered 70C and 50C chainsaws are exceptional tools for anyone seeking reliability and performance in the field. Whether for professional logging or home landscaping, these chainsaws embody the quality and innovation expected from the Jonsered brand.
Top Page Image Contents