Jonsered 70C, 50C manual General rules, Do not let go of the handles

Page 16

SAFETY INSTRUCTIONS

Kickback always occurs in the cutting plane of the bar. Normally the chain saw and bar are thrown backwards and upwards towards the user. However, the chain saw may move in a different direction depending on the way it was being used when the kickback zone of the bar touched the object.

Kickback only occurs if the kickback zone of the bar touches an object.

General rules

1If you understand what kickback is and how it happens then you can reduce or eliminate the element of surprise. By being prepared you reduce the risk. Kickback is usually quite mild, but it can sometimes be very sudden and violent.

2Always hold the chain saw firmly with your right hand on the rear handle and your left hand on the front handle. Wrap your fingers and thumbs around the handles. You should use this grip whether you are right-handed or left- handed.This grip minimises the effect of kickback and lets you keep the chain saw under control.

Do not let go of the handles!

3Most kickback accidents happen during limbing. Make sure you are standing firmly and that there is nothing in the way that might make you trip or lose your balance.

Lack of concentration can lead to kickback if the kickback zone of the bar accidentally touches a branch, nearby tree or some other object.

4Never use the chain saw above shoulder height and try not to cut with the tip of the bar. Never use the chain saw one-handed!

5In order to keep control of your saw, always maintain a firm foothold. Never work on a ladder, in a tree or on any other insecure support.

6Always use a fast cutting speed, i.e. full throttle.

7Take great care when you cut with the top edge of the bar, i.e. when cutting from the underside of the object. This is known as cutting on the push stroke. The chain tries to push the chain saw back towards the user.

Unless the user resists this pushing force there is a risk that the chain saw will move so far backwards that only the kickback zone of the bar is in contact with the tree, which will lead to a kickback.

Cutting with the bottom edge of the bar, i.e. from the top of the object downwards, is known as cutting on the pull stroke. In this case the chain saw pulls itself towards the tree and the front edge of the chain saw body rests naturally on the trunk when cutting. Cutting on the pull stroke gives the operator better control over the chain saw and the position of the kickback zone.

16 – English

Image 16
Contents Operator’s manual EPA KEY to Symbols Key to symbolsContents EPA Machine′s safety equipment Safety InstructionsPersonal protective equipment Chain brake and front hand guard Stop switch Throttle lockChain catcher Right hand guardMuffler Checking brake band wearChecking the front hand guard Checking the inertia brake releaseStop switch Throttle lockChain catcher Right hand guardCutting equipment General rulesCutting equipment designed to minimise kickback MufflerSharpening your chain and adjusting raker clearance ChainSome terms that describe the bar and chain General information on sharpening cutting teethGeneral advice on setting raker clearance Sharpening cutting teethSetting the raker clearance Tensioning the chainIf the raker clearance is too large Cause serious or even fatal injuryLubricating cutting equipment How to avoid kickback What is kickback?Checking wear on cutting equipment Chain drive sprocketDo not let go of the handles General safety precautions StartingFuel safety Basic safety rulesGeneral working instructions Transport and storageGeneral Basic cutting techniqueTerms Cutting LimbingTree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatFelling cut General advice Freeing a tree that has fallen badlyCutting the trunk into logs Freeing a trapped treeWhat is WHAT? What is what on the chain saw?Assembly Fitting the bar and chainFuel Fuel HandlingChain oil Fuelling Starting and Stopping Starting and stoppingCold engine Warm engineStopping Maintenance CarburettorCorrectly adjusted carburettor StarterChanging a broken or worn starter cord Tensioning the recoil springAir filter Spark plugMuffler Fitting the starterAdjustment of the oil pump Centrifugal cleaning TurboWhen making adjustments Needle bearing lubricationHeated handles Electrical carburettor heatingWinter use CanadaMonthly maintenance Daily maintenance Weekly maintenanceBelow you will find some general maintenance instructions Technical data Technical DataCS 2171/WH Bar Chain Length, inches Pitch, inch Max nose radius050/1,3 mm 058/1,5mmFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsPage 1088917-95

50C, 70C specifications

The Jonsered 70C and 50C chainsaws represent a pinnacle of craftsmanship and engineering excellence in the world of power tools. Designed for both professional and avid DIY enthusiasts, these models offer a blend of power, performance, and user-friendly features that elevate the cutting experience.

At the heart of both the Jonsered 70C and 50C is their powerful engine output. The 70C boasts a robust 70cc engine, delivering high torque and efficiency for demanding tasks, while the 50C is equipped with a nimble 50cc engine, perfect for lighter, more agile cutting projects. This versatility makes the chainsaws suitable for a wide range of activities, from felling trees to limbing and pruning, ensuring that they cater to varying user requirements.

One notable feature of the Jonsered 70C and 50C is their advanced air filtration systems. These systems are designed to enhance the longevity of the chainsaw's engine by preventing dust and debris from entering the combustion area. This means less maintenance and more time spent operating the chainsaw, making it an ideal choice for both professional lumberjacks and casual users.

Ergonomically designed, the handle of both models offers excellent grip and comfort, reducing user fatigue during extended use. The lightweight construction of the saws enables effortless maneuverability and control, allowing users to execute precise cuts without strain. Additionally, the quick and easy chain tensioning system facilitates fast adjustments, ensuring that the chain remains in optimal condition for continuous cutting.

Safety features are paramount in the design of the Jonsered 70C and 50C. Each model incorporates a chain brake and throttle lock to enhance user safety while operating, minimizing risks associated with kickback and accidental starts. The designs also emphasize low vibration, which further protects the user's hands and arms from fatigue, promoting a safer and more enjoyable cutting experience.

With their blend of power, efficiency, and advanced technology, the Jonsered 70C and 50C chainsaws are exceptional tools for anyone seeking reliability and performance in the field. Whether for professional logging or home landscaping, these chainsaws embody the quality and innovation expected from the Jonsered brand.