Jonsered 50C, 70C manual Tree felling technique, Safe distance, Felling direction

Page 21

SAFETY INSTRUCTIONS

Tree felling technique

WARNING! It takes a lot of experience to fell

!a tree. Inexperienced users of chain saws should not fell trees. Do not attempt any task that you feel unsure of!

Safe distance

The safe distance between a tree that is to be felled and anyone else working nearby is at least 21/2 tree lengths. Make sure that no-one else is in this ”risk zone” before or during felling.

Felling direction

The aim is to fell the tree in a position where you can limb and cross-cut the log as easily as possible. You want it to fall on ground where you can stand and move about safely.The main point to avoid is letting the tree fall onto another tree. See instructions under the heading Freeing a tree that has fallen badly.

Once you have decided which way you want the tree to fall you must judge which way the tree would fall naturally.

Several factors affect this:

•Lean of the tree

•Bend

•Wind direction

•Arrangement of branches

•Weight of snow

You may find you are forced to let the tree fall in its natural direction because it is impossible or dangerous to try to make it fall in the direction you first intended.

Another very important factor, which does not affect the felling direction but does affect your safety, is to make sure the tree has no damaged or dead branches that might break off and hit you during felling.

WARNING! During critical felling operations,

!hearing protectors should be lifted immediately when sawing is completed so that sounds and warning signals can be heard.

Clearing the trunk and preparing your retreat

Remove any branches that are in the way. To do this it is best to work from the top down and keep the trunk between you and the chain saw. Never limb above shoulder height.

Remove any undergrowth from the base of the tree and check the area for obstacles (stones, branches, holes, etc.) so that you have a clear path of retreat when the tree starts to fall.

Your path of retreat should be roughly 135 degrees away from the intended felling direction.

Felling

Felling is done using three cuts. First you make the directional cuts, which consist of the top cut and the bottom cut, then you finish with the felling cut. By placing these cuts correctly you can control the felling direction very accurately.

Directional cuts

To make the directional cuts you begin with the top cut. Stand to the right of the tree and cut on the pull stroke.

Next make the bottom cut so that it finishes exactly at the end of the top cut.

The directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut should be 45°.

English – 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Operator’s manual EPA Key to symbols KEY to SymbolsContents EPA Safety Instructions Machine′s safety equipmentPersonal protective equipment Chain brake and front hand guard Throttle lock Stop switchChain catcher Right hand guardChecking brake band wear MufflerChecking the front hand guard Checking the inertia brake releaseThrottle lock Stop switchChain catcher Right hand guardGeneral rules Cutting equipmentCutting equipment designed to minimise kickback MufflerChain Sharpening your chain and adjusting raker clearanceSome terms that describe the bar and chain General information on sharpening cutting teethSharpening cutting teeth General advice on setting raker clearanceTensioning the chain Setting the raker clearanceIf the raker clearance is too large Cause serious or even fatal injuryLubricating cutting equipment What is kickback? How to avoid kickbackChecking wear on cutting equipment Chain drive sprocketDo not let go of the handles Starting General safety precautionsBasic safety rules Fuel safetyGeneral working instructions Transport and storageBasic cutting technique GeneralTerms Limbing CuttingSafe distance Tree felling techniqueFelling direction Clearing the trunk and preparing your retreatFelling cut Freeing a tree that has fallen badly General adviceCutting the trunk into logs Freeing a trapped treeWhat is what on the chain saw? What is WHAT?Fitting the bar and chain AssemblyFuel Handling FuelChain oil Fuelling Starting and stopping Starting and StoppingCold engine Warm engineStopping Carburettor MaintenanceStarter Correctly adjusted carburettorChanging a broken or worn starter cord Tensioning the recoil springSpark plug Air filterMuffler Fitting the starterCentrifugal cleaning Turbo Adjustment of the oil pumpWhen making adjustments Needle bearing lubricationElectrical carburettor heating Heated handlesWinter use CanadaDaily maintenance Weekly maintenance Monthly maintenanceBelow you will find some general maintenance instructions Technical Data Technical dataCS 2171/WH Length, inches Pitch, inch Max nose radius Bar Chain050/1,3 mm 058/1,5mmYour Warranty Rights and Obligations Federal Emission Control Warranty StatementPage 1088917-95

50C, 70C specifications

The Jonsered 70C and 50C chainsaws represent a pinnacle of craftsmanship and engineering excellence in the world of power tools. Designed for both professional and avid DIY enthusiasts, these models offer a blend of power, performance, and user-friendly features that elevate the cutting experience.

At the heart of both the Jonsered 70C and 50C is their powerful engine output. The 70C boasts a robust 70cc engine, delivering high torque and efficiency for demanding tasks, while the 50C is equipped with a nimble 50cc engine, perfect for lighter, more agile cutting projects. This versatility makes the chainsaws suitable for a wide range of activities, from felling trees to limbing and pruning, ensuring that they cater to varying user requirements.

One notable feature of the Jonsered 70C and 50C is their advanced air filtration systems. These systems are designed to enhance the longevity of the chainsaw's engine by preventing dust and debris from entering the combustion area. This means less maintenance and more time spent operating the chainsaw, making it an ideal choice for both professional lumberjacks and casual users.

Ergonomically designed, the handle of both models offers excellent grip and comfort, reducing user fatigue during extended use. The lightweight construction of the saws enables effortless maneuverability and control, allowing users to execute precise cuts without strain. Additionally, the quick and easy chain tensioning system facilitates fast adjustments, ensuring that the chain remains in optimal condition for continuous cutting.

Safety features are paramount in the design of the Jonsered 70C and 50C. Each model incorporates a chain brake and throttle lock to enhance user safety while operating, minimizing risks associated with kickback and accidental starts. The designs also emphasize low vibration, which further protects the user's hands and arms from fatigue, promoting a safer and more enjoyable cutting experience.

With their blend of power, efficiency, and advanced technology, the Jonsered 70C and 50C chainsaws are exceptional tools for anyone seeking reliability and performance in the field. Whether for professional logging or home landscaping, these chainsaws embody the quality and innovation expected from the Jonsered brand.
Top Page Image Contents