Jonsered 2054 manual Changing a broken or worn starter cord, Starter device assembly

Page 30

MAINTENANCE

Starter device

!WARNING!

•When the recoil spring is assembled in the starter housing, it is in tensioned position and can when treated carelessly, pop out and cause injuries.

•Always be careful, when changing the recoil spring or the starter cord. Always wear safety goggles for eye protection.

Changing a broken or worn starter cord

• Loosen the screws, that hold the starter device against the crankcase and remove the starter device.

• Pull out the cord approx. 30 cm and lift it up into the notch in the pulley. Zero-set the recoil spring by letting the pulley rotate slowly backwards. Undo the screw in the centre of the pulley and remove the pulley.

•Insert and fasten a new starter cord in the pulley. Wind approx. 3 turns of the starter cord on to the pulley. Assemble the starter pulley against the recoil spring, so the end of the spring engages to the pulley. Fit the screw in the centre of the pulley. Carry the starter cord through the hole in the starter housing and the starter handle. Make a knot on the starter cord.

Tensioning the recoil spring

•Lift the starter cord up in the notch on the starter pulley and turn the starter pulley 2 turns clockwise.

NOTE! Check that the starter pulley can be turned at least half a turn, when the starter cord is entirely pulled out.

Changing the broken recoil spring

•Lift the starter pulley. (See, ”Changing a broken or worn starter cord”). The recoil spring is disassembled from the starter device, with its inside facing down. Tap the starter lightly against a working bench or similar.

•Put a new recoil spring in the right position. If the spring pops out when assembling, it should be mounted again, out and in towards the centre.

•Lubricate the recoil spring with thin oil. Assemble the starter pulley, and tension the recoil spring.

Starter device assembly

•Assemble the starter device, by pulling the starter cord out first, then place the starter against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Assemble and tighten the screws, which hold the starter.

30 – English

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Operator´s manual EPA KEY to Symbols SymbolsContents Safety Instructions Personal Protective EquipmentChain brake and front hand guard Throttle lock Chain catcherRight hand guard Stop switch Vibration damping systemMuffler Checking the automatic brake Checking brake band wearChecking the front hand guard Checking the brake triggerThrottle lock Cutting Equipment 5 basic rulesSaw chain Cutting equipment designed to minimise kickbackBar Some terms that describe the bar and chainSharpening your chain and adjusting raker clearance General information on sharpening cutting teethSharpening cutting teeth General advice on setting raker clearance Setting the raker clearanceTensioning the chain Filling with chain oil Lubricating cutting equipmentChain oil Never use waste oilChecking wear on cutting equipment Checking chain lubricationLubricating the clutch drum bearing Lubricating the bar tip sprocketHOW to Avoid Kickback What is kickback?General rules Do not let go of the handlesNever use the saw one- handed Min m 10 ftBasic safety rules General Working InstructionsTerms Basic cutting techniqueGeneral CuttingLimbing Tree felling techniqueSafe distance Felling directionClearing the trunk and preparing your retreat FellingCutting the trunk into logs General adviceFreeing a tree that has fallen badly = high accident risk Freeing a Trapped treeWhat is WHAT? What is what?Assembly Mounting guide bar and chainFuel Handling Fuelmix10 ft Oil pumpFuelling Min mStart and Stop Start and stopMaintenance CarburetorChanging a broken or worn starter cord Starter device assemblyStarter device Tensioning the recoil springMuffler Needle bearing maintenanceAir filter Spark plugWinter use Centrifugal cleaning TurboCooling system Electrically heated handles or carburetorWeekly maintenance Daily maintenance Monthly maintenanceTechnical Data 2054Federal Emission Control Warranty Statement Your Warranty Rights Obligations108 87 1998W48

2054 specifications

The Jonsered 2054 is a high-performance chainsaw designed for both residential and professional use, offering a blend of power, reliability, and advanced technology. Known for its durability and efficiency, the 2054 has garnered a reputation among users who require effective cutting tools for various tasks, from tree felling to firewood preparation.

One of the standout features of the Jonsered 2054 is its powerful engine. Equipped with a robust 54cc two-stroke engine, it delivers impressive power to tackle demanding cutting jobs with ease. The engine is designed with advanced fuel technology, allowing for a more efficient combustion process that not only increases power output but also improves fuel economy. This ensures that users can work longer without frequent refueling, making it an ideal choice for extended use.

The chainsaw incorporates a low-vibration system, which significantly reduces user fatigue during operation. This technology dampens vibrations produced during cutting, ensuring a smoother experience and promoting more precise cuts. The ergonomic handle design further enhances comfort, allowing users to maintain a firm grip without straining their hands over prolonged periods.

Safety is a top priority with the Jonsered 2054, as it is equipped with several protective features. The chainsaw comes with a chain brake mechanism that halts chain movement in the event of kickback, minimizing the risk of injury. Additionally, the easy-access air filter and tool-less chain tensioning system simplify maintenance tasks, allowing users to keep their equipment in top condition without the hassle of complicated procedures.

The Jonsered 2054 also boasts a powerful cutting system, utilizing a high-quality cutting chain and bar that ensures smooth and efficient cutting. The balanced design of the saw contributes to its maneuverability, enabling users to navigate tight spaces with ease when performing detailed work.

Overall, the Jonsered 2054 combines power, comfort, and safety in a well-engineered package. It's a versatile tool suited for a wide range of cutting tasks, and its advanced technologies ensure that it delivers consistent performance even under challenging conditions. Whether for personal or professional use, the Jonsered 2054 is a reliable choice that meets the demands of modern forestry and landscaping needs.
Top Page Image Contents