Jacuzzi SteamPro manual Symptoms Probable Causes, Off

Page 19

TROUBLESHOOTING

SYMPTOMS

PROBABLE CAUSES

Control "ON".

Unit has not filled completely.

(Control light on)

Heating elements burnt out.

Unit won'tsteam.

Level probe faulty.

 

"PCA" printed circuit assembly is

Note: Steam lit

faulty.

steadily or

 

Time/Temp properly

 

displayed on Digital

 

Display

 

Control "ON".

Temperature sensor not connected.

Digital Control

 

displays "E001"

 

Control "ON".

Temperature sensor or cable shorted.

Digital Control

 

displays "E002"

 

Control "ON".

Control improperly connected.

Digital Control

 

displays "E003"

 

Control "ON".

Steambath temperature over 132°.

Digital Control

Sensor/cable faulty.

displays ">>>º"

 

Control "ON".

Control improperly connected.

"STEAM" LED light

Sensor/cable faulty.

blinking

Control faulty.

Control won'tturn

Control is faulty.

"OFF"

 

(Control light off).

 

Control "OFF"

"PCA" printed circuit assembly is

Unit won'tshut off.

faulty.

Water continually

Foaming contaminants in the water.

sputters out of steam

 

head.

 

Unable to adjust

Control faulty.

Time or Temp setting

"PCA" printed circuit assembly is

with Digital Control

faulty.

ACTION TO BE TAKEN

1.a. Push the control "OFF".

b.Open the drain valve allowing tank to drain completely.

c.Close the drain valve.

d.Push the control "ON".

e.Unit will begin filling, listen for a click noise. Within 20 seconds after click noise is heard, the water fill will shut off. This will indicate the tank is full. Go to step 3, if the tank does not fill - See SYMPTOMS: "Unit won'tfill up".

2.If the tank filled but the relay click was not heard, temporarily ground the two long probes. If the click is heard as each probe is grounded, replace the level probe. If the click is not heard replace the "PCA" printed circuit assembly.

3.After it has been determined that the tank has filled and the click noise was heard, remove the heating element access panel. Using a voltmeter, check the voltage between the two wires on each heating element - the voltage should be 208V/240V. If proper voltage is found call the factory for replacment heating elements. If no voltage is found - check wiring diagram - call Service Deparment.

1.Check that the sensor cable is connected to J4 on the "PCA" printed circuit assembly.

2.Check the cable connection to the temperature sensor.

3.Replace sensor and/or cable - call Service Department.

1.Check sensor cable for damage from nail/staple puncture.

2.Check sensor cable ends for frayed/exposed wire strands.

3.Replace sensor and/or cable - call Service Department.

1.Check that the control cable is properly plugged in at the control and at the generator. Digital Control to primary SK3 connector on the PCA. Turn off power supply, wait one (1) minute then turn back on. Check for proper operation. If "E003" is still displayed turn off power supply, remove control cable and plug into secondary SK4 connector. Turn on power supply and check for proper operation. If "E003" is still displayed turn off power and call Service Department.

1.If bath is too hot, shut off circuit breaker and call Service Department.

2.Treat as "E002" fault above.

1.Check that the control cable is properly plugged in at the control and at the generator. Connect Control to primary SK1 connector on the PCA. Turn off power supply, wait one (1) minute then turn back on. Check for proper operation. If "STEAM" is still "blinking", turn off power supply and call Service Department.

2.Check sensor/cable as with Digital "E001" and "E002"

3.Replace Control - call Service Department.

1.Replace the control - call Service Department.

1.Turn off the power to the generator, replace printed circuit assembly - call Service Department.

1.Flush tank 3 times. See section 8, flushing procedure.

2.Call Service Department.

1.Replace control - call Service Department.

2.Replace PCA - call Service Department.

17

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Steampro TM Important Safety Information Contents How to Select Generator Size InstallationElectrical Requirements Room Construction and Ventilation Important Locating the Steam GeneratorPlumbing Instructions and Cautionary Notes on Installation Plumbing Diagram Steam Head Installation for Various Wall Surfaces KW Steam Generator with Two Steam Heads Important Note About Tank Drain Selection Automatic Drain Valve Installation OptionalOutlet must point as shown Steam Controls-Available Installation Methods Control cable at the generator Install generator control R30iSteam Control by 30 Minute LOW Voltage ON/OFF Control Control cable rough-inElectrical finish General Instructions for Temperature Control ModelsTemperature Sensor Rough-in Electrical Rough-inInstall Temperature Sensor Install Generator ControlOptional Secondary Generator Control Operation Minute Temperature ControlOperation of Your 30 Minute Temperature Control Temperature AdjustmentOperation of Your Digital Time and Temperature Control Digital Time and Temperature ControlRepair of SteamPro Generators ServiceMaintenance of SteamPro Generators Description of SteamPro Steam GeneratorSymptoms Probable Causes Action to be Taken TroubleshootingOFF Symptoms Probable CausesJacuzzi Whirlpool Bath Wiring DiagramJacuzzi Whirlpool Bath National Headquarters Amerec Name of Purchaser Address City Zip Phone

SteamPro specifications

The Jacuzzi SteamPro is an innovative steam shower system designed to elevate your home spa experience, offering a blend of relaxation and wellness. Known for its sleek design and advanced technology, the SteamPro is not just a steam generator; it embodies the essence of luxury and comfort.

One of the standout features of the SteamPro is its ability to produce high-quality steam quickly and efficiently. The advanced steam generator utilizes a patented technology that ensures rapid heating, allowing users to enjoy soothing steam in less time. This efficiency is complemented by customizable steam settings, which enable you to adjust the intensity and duration of your steam sessions to suit your personal preferences.

The SteamPro also incorporates a user-friendly control panel, featuring a digital display that allows for easy navigation and access to various functions. This interface gives users the ability to program personalized steam sessions, including pre-set temperature levels and aromatherapy options. The inclusion of essential oil dispensers enhances the experience, filling your space with calming scents that promote relaxation and well-being.

In terms of technology, the SteamPro is equipped with an advanced water softening system that minimizes mineral buildup, ensuring longevity and optimal performance. This system not only protects the unit but also contributes to cleaner steam, enhancing the overall shower experience. The design also allows for efficient drainage, preventing water from pooling and maintaining a clean environment.

Safety is a top priority with the SteamPro, which incorporates features such as automatic shut-off functions to prevent overheating and overpressure. The steam generator is constructed from high-quality materials that resist corrosion and wear, ensuring durability and reliability over time.

The SteamPro’s compact design makes it an ideal choice for various bathroom layouts, easily integrating with both new and existing setups. Its stylish aesthetics add a modern touch to any space, making it not just a functional piece of equipment, but also a stylish addition to your home.

In summary, the Jacuzzi SteamPro is a pinnacle of steam shower technology that combines efficiency, safety, and luxury. With customizable features, advanced materials, and user-friendly design, it represents a significant advancement in home wellness solutions, allowing users to transform their daily routine into a spa-like retreat. Whether it’s for relaxation or therapeutic benefits, the SteamPro provides an unparalleled steam shower experience.
Top Page Image Contents