Marantz SR6300 manual Playback Operation, TV Auto ON/OFF Function, Normal Playback, Auto Power on

Turn ON the TV TUNER and tune in a receivable station.

STATION NAME PRESET (On PRESET display mode)

The station name preset function allows the name of each preset channel to be entered using alphanumeric characters. The Station Name button is valid only in the tuner mode. Before station name preset operation, store stations with the preset memory operation.

1. Press the MEMORY button !3on the front panel or MEMO button ¤6on the remote for more than 3 seconds.

2. The left most column of the station name indicator flashes, indicating the character entry ready status.

[Operation (Using the SR6300)]

3. When you press the TUNING/PRESET or buttons !4is turned, alphabetic and numeric characters will be displayed in the following order:

A → B → C ...Z → 1 → 2 → 3..... 0 → – → + → / → (Blank) → A

UP →

←DOWN

4.After selecting the first character to be entered, press the MEMORY button !3. The entry in this column is fixed and the next column starts to flash. Fill the next column and press the MEMORY button !3for more than 1 second to confirm the entry.

[Operation (Using the remote control unit)]

First, press the TUNER button ⁄9on the remote control unit.

(This operation is not necessary if the remote control unit has already been operated in the TUNER mode.)

3. Enter the character using the ten keypad ,. For example, to enter “A”:

1)Press the “1” button. “A” appears on the display column.

2)Every time the 1 button is pressed, the displayed character changes in the order: A → B → C → 1 → A...

Pressing buttons other than the “1” button cause different characters to be displayed in a similar way, so that other alphanumeric characters can be entered. To enter a blank or space, press the “9” button.

4. When the desired character is displayed, press the MEMO button ¤6to confirm the entry in this column and move to the next column. After having filled all of the 8 columns, press the MEMO button ¤6, for more than 1 second to confirm the entry.

	PLAYBACK OPERATION
			ENGLISH
	NORMAL PLAYBACK
1.		Press the POWER button q / ‹4.
2.		Press the desired FUNCTION SELECTOR button t on the front
		panel or press the desired FUNCTION button ⁄9on the remote
3.		unit to select an input source.
		Turn the SURROUND MODE SELECTOR knob e on the front
		panel or Surround mode buttons , in the AMP MODE on the
4.		remote unit to select the desired surround mode.
		Adjust the volume level using the VOLUME knob r on the front
		panel or press the VOL. button ¤3on the remote. If necessary,
		adjust the tone, press the TREBLE , TREBLE ⁄4and BASS ,
		BASS ⁄4on the remote unit.

Note:

•In case of remote control operation, press one of the function buttons twice within 2 seconds to select the function.

LISTENING TO A DIFFERENT AUDIO SOURCE WHILE WATCHING A VIDEO SOURCE (Using the remote control unit)

1. Select one of the following video sources TV, DVD, VCR1, DSS/VCR2 or AUX.

2. Next, select one of the following audio sources FM, AM, CD, TAPE, or CDR/MD.

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the TV IN jack to control the power (ON/OFF) to the SR6300.

AUTO POWER ON

1. Be sure TV auto mode is enable. (Refer page 18 : PREFERENCE)

2. Connect your TV TUNER (etc) to the TV IN terminal.

Be sure to connect the video input.

3. Turn OFF the power to the TV TUNER and the SR6300 will be in standby mode.

4.

5. When the station is received, the SR6300 turns ON and TV is selected automatically.

AUTO POWER OFF

1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast.

2. The SR6300 switches to STANDBY after approximately 5 minutes.

Note:

•AUTO POWER OFF is canceled if the FUNCTION SELECTOR button t is set to a source other than TV. The function reactivates when TV is selected again.

Caution:

•Some TV broadcasts may cause the TV AUTO FUNCTION to turn on.

•S-Video termianl does not support “TV AUTO ON/OFF” function.

21