2. Auto Presetting
This function automatically scans the LW, MW and FM band and enters all stations with proper signal strength into the memory.
This function is available only for SR-14EX.
1.Select the FM band with the BAND button y.
2.Tune in the lowest receivable frequency.
3.While pressing the MEMO button i, turn the GYRO TUNING knob @1to up. Auto memory starts at this point.
4.“MEMO ” will blink on the display.
5.Each time the tuner finds a station, the scanning will pause and the station will be played for five seconds. During this time, the following operations are possible:
1)The band can be changed using the BAND button y.
2)The mode can be changed using the FM MODE button u.
6.If no button is pressed during this period, the current frequency is preset in location CH-2. If you wish to skip the current station, turn the GYRO TUNING knob @1during this period, the current frequency is skipped and auto presetting continues.
7.Operation stops automatically when all 50 preset memory positions are filled or when auto scanning attains the highest end of all bands. To stop the auto preset function at anytime, press the CL (CLEAR) button o.
3.Recalling a Preset Station
1.Press the PRESET button !8to change the display to preset.
2.Select the desired preset station by turning GYRO TUNING knob @1on the front panel or press ^ Skip v button on page of Tune mode on the remote.
Note;
•Direct selection method using the ten keypad on the remote, select the desired preset station by entering one or two digits using the ten keypad on page of keypad mode on the remote.
•To return to the Manual Tuning mode, press the AUTO TUNING button !7.
4.Preset Scan Tuning (Using the remote control unit)
1.Press the Preset Scan on page of Tune mode on the remote. “P- SCAN” indicator blinks in the display. (The preset station with the smallest preset number is recalled first. If no stations have been preset, CH “00” blinks in the display and the unit returns to the previous mode.)
2.Preset stations are recalled in sequence (CH-1 › CH-2, etc.) for 5 seconds each. Preset numbers that do not contain stations are skipped.
3.You can fast forward the preset stations by pressing the Skip ^ button continuously. When the desired preset station is received, cancel the preset scan operation by pressing the Skip v button or the Preset Scan button or Clear button.
5.Clearing Preset Stations
You can remove preset stations from memory using the following procedure.
1.Recall the preset number to be cleared with the method described in “Recalling” a preset station .
2.Press the MEMO button i on the front panel or Memo button on page of Tune mode on the remote unit, “MEMO” blinks in the display for 5 seconds. While “MEMO” is still blinking, press the CL (CLEAR) button o on the front panel or Clear button on page of Tune mode on the remote unit. “CLEAR” appears on the display to indicate that the specified preset number has been cleared.
STATION NAME PRESET
| The station name preset function allows the name of each preset | ENGLISH |
| channel to be entered using alphanumeric characters. The Station |
| |
| Name button is valid only in the tuner mode. Before station name | |
| preset operation, store stations with the preset memory operation. | |
| 1. | Press the MEMO button i on the front panel or Memo button on | |
| | page of Tune mode on the remote for more than 3 seconds. | |
| 2. | The left most column of the station name indicator flashes, | |
| | indicating the character entry ready status. | |
[Operation (Using the SR-14EX)]
3.When the GYRO TUNING knob @2is turned, alphabetic and
numeric characters will be displayed in the following order:
A → B → C ...Z → 1 → 2 → 3..... 0 → – → + → / → (Blank) → A
UP →
←DOWN
4.After selecting the first character to be entered, press the MEMO button i. The entry in this column is fixed and the next column starts to flash. Fill the next column and press the MEMO button i for more than 1 second to confirm the entry.
Note:
Unused columns should be filled by entering blanks.
[Operation (Using the remote unit)]
3.Enter the character using the ten keypad on page of Keypd mode. For example, to enter “A”:
1)Press the “1” button. “A” appears on the display column.
2)Every time the 1 button is pressed, the displayed character
changes in the order: A → B → C → 1 → A...
Pressing buttons other than the “1” button cause different characters to be displayed in a similar way, so that other alphanumeric characters can be entered. To enter a blank or space, press the “9” button.
4.When the desired character is displayed, press the Memo button on page of Keypad mode to confirm the entry in this column and move to the next column. After having filled all of the 8 columns, press the Memo button, or more than 1 second to confirm the entry.
DIRECT FREQUENCY CALL
1.Press the F/P button on page of Keypad mode on the remote.
2.Front display will show “FREQ ----”.
3.Input your desired frequency with Ten keypad button on the remote.
PLAYBACK OPERATION
NORMAL PLAYBACK
1.Press the POWER ON button on the remote.
2.Turn the INPUT SELECTOR !5on the front panel or press the FUNCTION buttons on page of Input mode on the remote unit to select an input source.
3.Press the Surround mode buttons e on the front panel or desired surround mode buttons page of Surround mode on the remote unit to select.
4.Adjust the volume level using the VOLUME knob !6on the front panel or press the VOLUME + / – buttons on the remote. If necessary, adjust the tone using the Bass and Treble buttons on page of Tone mode on the remote unit.
LISTENING TO A DIFFERENT AUDIO SOURCE WHILE WATCHING A VIDEO SOURCE (Using the remote control unit)
1.Select one of the following video sources TV, LD, DVD, VCR1, DSS/VCR2 or AUX.
2.Next, select one of the following audio sources FM, AM, CD, TAPE, or CDR/MD.
