Homelite UT13120 manual Sharpening the Blade, Balancing the Blade, FAN Assembly Shaft Blade Spacer

Page 15

MAINTENANCE

Place the new blade on the shaft against the fan assembly. Make sure it is installed with the curved ends pointing

up toward the mower deck and not down toward the ground.

Replace the blade insulator and spacer, then thread the blade nut on the shaft and finger tighten.

NOTE: Make certain all parts are replaced in the exact order in which they were removed.

Torque the blade nut down using a torque wrench (not provided) to ensure the bolt is properly tightened. The recommended torque for the blade nut is 450- 600 in. lbs.

SHARPENING THE BLADE

See Figure 14.

For best mowing performance, the mower blade must be kept sharp. A dull blade does not cut grass evenly and over-

FAN ASSEMBLY

SHAFT

BLADE

SPACER

BLADE NUT

 

loads the motor. Under normal circumstances, sharpening the blade twice during the mowing season is usually suf- ficient. However, if your lawn has sandy soil, more frequent sharpenings may be required.

Following the instructions in the Replacing the Cutting Blade section, remove the mower blade. DO NOT attempt to sharpen the blade while it is attached to the mower.

WARNING:

When removing, inspect the blade carefully. If blade is bent or damaged, replace immediately with a new blade. Failure to replace a bent or damaged blade could cause an accident resulting in possible serious injury.

�Using a fine-tooth file or stone, sharpen cutting edges on both ends of the blade, removing equal amounts of material from both ends.

BALANCING THE BLADE

See Figure 15.

When sharpening, care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibra- tion when the mower is running. This vibration will eventually cause damage to the mower, especially the motor.

To check the blade balance:

BLADE INSULATOR

Fig. 13

Fig. 14

Clamp a screwdriver horizontally in a vise as shown.

NOTE: If a vise is not available, a straight nail can also be used.

Place the center hole of blade on the screwdriver (or nail) shank.

If blade is balanced, it will remain in a horizontal position. If either end of the blade drops downward, sharpen the heavy side until the blade is balanced.

Page 15

Fig. 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Save this Manual for Future Reference OPERATOR’S ManualIntroduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules Name DESIGNATION/EXPLANATION SymbolsSymbol Signal Meaning ServiceElectrical Connection Cord Length Wire Size A.W.GElectrical Double InsulationUT13120 FeaturesProduct Specifications UT13118Assembly Adjusting Handle Installing Side Discharge DeflectorInstalling the Mulching Plug To set the blade height Installing the Grass CatcherSetting Blade Height Door ROD Height Adjustment LeverMowing Tips OperationApplications STARTING/STOPPING the MowerEmptying the Grass Catcher Model UT13120 only Slope OperationLubrication MaintenanceGeneral Maintenance Replacing the Cutting BladeTo check the blade balance FAN Assembly Shaft Blade SpacerSharpening the Blade Balancing the BladeTo lower the handle before storing Replacing WheelsStoring the Mower To replace a wheelProblem Possible Cause Solution TroubleshootingExploded VIEW/PARTS List Model UT13118Key Part Description Qty Key Part Description This Warranty is not Transferable and does not Cover Warranty Limited Warranty for Corded Electric ModelsPage Homelite Consumer PRODUCTS, INC

UT13120, UT13118 specifications

The Homelite UT13118 and UT13120 are two standout models in the domain of consumer-grade string trimmers, showcasing advanced design, power, and functionality intended for efficiency in lawn care. Both models cater to homeowners and garden enthusiasts looking for reliability and ease of use in maintaining their lawns.

The UT13118 features a robust 26cc two-cycle engine, delivering impressive power for various trimming tasks. Its lightweight structure allows for easy maneuverability, which is particularly valuable during extended periods of use. This model comes equipped with a 17-inch cutting width, enabling it to cover large areas efficiently while providing a clean finish. One of the significant highlights is its automatic feed spool system, which ensures a continuous supply of trimming line, minimizing downtime for users.

In contrast, the UT13120 is slightly more powerful with a 31cc engine. This additional power translates into enhanced cutting performance, making it suitable for tougher shrubs and thicker grass. The design follows an ergonomic approach, featuring a fully adjustable handle that accommodates various user heights and preferences, promoting comfort during prolonged operation. Like the UT13118, the UT13120 is equipped with a 17-inch cutting width, ensuring efficiency in every pass.

Both models utilize a quick-start technology that allows for easy ignition, reducing the hassle of traditional pull-starts. This feature is particularly appreciated by users seeking convenience without sacrificing performance. The trimmers boast a dual-line bump feed head that not only increases cutting versatility but also simplifies the process of replacing the trimming line.

Additionally, the Homelite UT13118 and UT13120 models are designed with durability in mind. Made from high-quality materials, they withstand the rigors of outdoor use while requiring minimal maintenance. Their compact designs facilitate easy storage and transport, making them practical choices for residential users.

Overall, the Homelite UT13118 and UT13120 are exemplary choices for those in search of a dependable, efficient, and user-friendly string trimmer. Whether you’re maintaining a small garden or tackling larger lawns, both models promise to deliver optimal results, ensuring that your outdoor space remains well-groomed and inviting.
Top Page Image Contents