Harbor Freight Tools 92199, 91839, 91840 manual Unpacking, Assembly, Attaching the Tires

Page 4

22.Never split a log that contains any foreign materials.

23.WARNING: The brass components in this product contain lead, which is a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. (California Health & Safety Code § 25249.5, et seq.)

24.People with pacemakers should consult their physician(s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker.

Warning:The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be under- stood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.

Unpacking

When unpacking, check to make sure the parts listed on page 9 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible.

Assembly

Note: Because of the weight and size of the Log Splitter, assembly should be done with the help of another person.

Attaching the Tires

Refer to the Assembly Drawing on page 9 and FIGURE 1 on page 5.

1.Position the Tires (48) next to each of the Axles located on the bottom of the Oil Tank Assembly (10). The Tires (48) come completely assembled.

2.Make certain to pack the bearings as explained in the included insert.

3.Put a Seal (59) and Bearing (49) on the Axle and then put the Tire (48) on the Axle.

4.Follow the Bearing Packing Instructions as explained on the last page of this manual. With each Tire (48) in place, add a Washer (50) and a Spindle Nut (51) onto the ends of the Axles. Tighten the Spindle Nuts (51) to 20-25 ft. pounds, and turn each tire several times to seat the bearing. Back off the Spindle Nut (51) one half turn. Insert a Cotter Pin (25) through both the Axle and the Spindle Nut (51) and bend the end of the Pin back to hold it in place. Lastly, tap on a Wheel Cap (61).

The Tire (48) assembly is now complete. Note: It may be necessary to reset the wheel bearings after the Log Splitter has been towed.

The wheel manufacturer states the maximum speed is not to exceed 40 MPH. The tires are DOT approved for public roads; however, this item is not for use on public roads or highways.

 

91839, 91840

 

REV 11/04

SKUs

For replacement parts, please call 1-800-444-3353.

Page

 

& 92199

 

 

Page 3 Page 5
Image 4
Page 3 Page 5
Contents For technical questions or replacement parts, please call Distributed exclusively by Harbor Freight ToolsSpecifications Safety Warnings and PrecautionsRead all instructions before using this tool For replacement parts, please callNever leave the Log Splitter unattended while in operation Never attempt to split two logs on top of each otherUnpacking AssemblyAttaching the Tires Connecting the Rail Assembly 2 to the Oil Tank Assembly 10B Place Log HereOperation TransportationThrottle Choke Starter Cord Maintenance Bleeding the Hydraulic SystemParts List Part Description QtyAssembly Drawing Seal Hydraulic Ram SealsKits Bearing Packing Instructions Hydraulics Drawing

91840, 92199, 91839 specifications

Harbor Freight Tools offers an array of high-quality tools and equipment, among which the models 91839, 92199, and 91840 stand out for their functionality, versatility, and reliability. These tools are designed to meet the needs of both professional tradespeople and DIY enthusiasts, making them essential additions to any workshop.

The Harbor Freight Tools 91839 model is a compact air compressor that delivers an impressive performance in a space-saving design. It features a powerful 1.5 HP motor that generates sufficient air pressure for various pneumatic tools. The 91839 is equipped with a large 4-gallon tank, allowing for extended use without frequent cycling. Its lightweight and portable design come with a comfortable handle, making it easy to transport from one job site to another. Additionally, the unit operates quietly, minimizing noise pollution during use, which is particularly advantageous for residential areas.

The 92199 model, on the other hand, is a versatile tool chest that brings organization and efficiency to any garage or workshop. Constructed from durable steel, this tool chest boasts a sleek powder-coated finish that resists scratches and corrosion. With multiple drawers of varying sizes, users can easily store and access their tools, while a built-in lock ensures security. The ball-bearing slides allow for smooth opening and closing of drawers, even when fully loaded. Its ample storage space, combined with a compact footprint, makes it an excellent choice for users looking to maximize their workspace.

The Harbor Freight Tools 91840 is a high-performance impact wrench that delivers impressive torque, making it suitable for a wide range of applications, from automotive repairs to construction projects. Featuring a powerful motor, this impact wrench can effortlessly drive and remove fasteners with ease. Its compact design ensures that it can access tight spaces, providing users with versatility in various working environments. Moreover, the ergonomic handle offers a comfortable grip, reducing fatigue during prolonged use.

In summary, Harbor Freight Tools models 91839, 92199, and 91840 each bring unique features and technologies that cater to the demands of today’s professionals and hobbyists alike. From the efficient air compressor to the rugged tool chest and the powerful impact wrench, these tools exemplify quality and reliability, ensuring that users can tackle any project with confidence.
Top Page Image Contents