Guardian Technologies 4582 & 4987 Test 8 DIODE/RESISTOR, Set volt meter to the diode test range

Page 44

Section 6

DIAGNOSTIC TESTS

1616

8717

1586 87a 85

30

OL

14

WIRE 14

REMOVED 14

13

WIRING DIAGRAM

R1

30

87a

87

D2

8586

Figure 6-13. – Starter Contactor Relay

3.0 vdc

14

R1

14

D2

4

4

Figure 6-14. – Testing Field Boost

TEST 8 - DIODE/RESISTOR

PROCEDURE:

1.Set volt meter to the diode test range.

2.Disconnect the six pin connector from the Voltage Regulator.

3.Disconnect Connector C1. See Page 17 for connector location.

4.Disconnect both wires from the Resistor (R1).

5.Connect the positive meter test lead to the top terminal of the diode (D1). Connect the negative meter test lead to the bottom of the diode (D1). See Figure 6-15. INFINITY or an open condi- tion should be measured.

4

4

Figure 6-15. – Diode Test Step 5

6.Connect the positive meter test lead to the bottom terminal of the diode (D1). Connect the negative meter test lead to the top of the diode (D1). Approximately 0.5 Volts should be measured.

.5 vdc

14

WIRE 14

REMOVED 14

R1

D2

4

4

Figure 6-16. – Diode Test Step 6

7.Set volt meter to measure resistance.

8.Connect one meter test lead to the top terminal of the diode (D1). Connect the other meter test lead to the ground terminal. INFINITY or an open condition should be measured.

9.Connect one meter test lead to one terminal of the resistor (R1). Connect the other meter lead to the remaining terminal of resistor (R1). See Figure 6-17. Approximately 25 ohms should be measured.

Page 42

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Diagnostic Repair Manual Safety Replacement PartsTable of Contents Section Disassembly and Exploded Views 66-71 Electromagnetic Induction MagnetismElectromagnetic Fields More Sophisticated AC Generator STATORs AC power windingsSimple AC Generator Generator Operating Diagram Meters Measuring AC VoltageVOM Measuring DC VoltageMeasuring Current Measuring ResistanceElectrical Units Ohms LawEngine-Generator Drive System Rotor AssemblyIntroduction AC Generator Stator Assembly Brush Holder and BrushesOther AC Generator Components Excitation Circuit BreakerVoltage Regulator Underfrequency Adjust162 Operation Rotor Residual MagnetismField Boost Circuit Stator Insulation Resistance Test Insulation ResistanceMegohmmeter Testing ALL Stator Windings to Ground Test Between WindingsDrying the Generator Cleaning the GeneratorRotor Insulation Resistance Test Battery Recommended BatteryPrinted Circuit Board Circuit Board ConnectionsControl Panel Component Identification ENGINE DC CONTROLTerminal Block Terminal BLOCKTB2 TB1 C1 Female Side C1 Male SideC2 Female Side C2 Male Side Page Circuit Condition Rest = 12 VDC Control Circuit Condition Start IM1 SP1 IM2 SP2 RED Black Battery Circuit Condition RUN = Idle Control Transformer Output CIRcUIT Condition Stop Fault Shutdown Introduction If Problem Involves AC OutputProblem 1 Voltage & Frequency Are Both High or Low Or Replace If BAD Load Watts Problem 4 No Battery Charge Output Problem 5 No 10A Battery Charge OutputProblem 6 Engine Will Not Crank Problem 7 Engine Cranks But Will Not Start Problem 8 Engine Starts Hard and Runs Rough Problem 9 Engine Starts Then Shuts DownProblem 10 10 Amp Fuse F1 Blowing Problem 14 Engine Hunts / Erratic Idle Problem 11 Unit OverspeedsProblem 12 Idle Control RPM Does Not Decrease Procedure Test 1 Check No-Load Voltage FrequencyTest 2 Check Main Circuit Breaker ResultsSet voltmeter to measure AC voltage Test 4 Fixed Excitation Test Rotor AMP DrawIf circuit breaker is good, go on to Test AC Voltage across Wires 11S and 44S= Refer to Test 4 Results chartRemove air cleaner cover to access stepper motor Set a voltmeter to measure resistanceTest 6 Wire Continuity Test 7 Check Field BoostDisconnect both wires from the Resistor R1 Test 8 DIODE/RESISTORSet volt meter to the diode test range Set volt meter to measure resistanceFrom the 50 Amp receptacle disconnect Wire Test 9 Test StatorUnplug the six pin connector at the Voltage Regulator Test 10 Sensing LeadsTest 11 Excitation Wiring Gain access to the brushes and slip ringsTest 12 Check Brush Leads Test 13 Check Brushes & Slip RingsTest 14 Check Rotor Assembly Test 15 Check Load Voltage FrequencyTest 16 Check Load Watts & Amperage If the unit is overloaded, reduce the loadDisconnect all wires from the Battery Charge Rectifier Test 17 Check Battery Charge OutputTest 19 Check Battery Charge Rectifier BCR2 BCR1BCR2 Test 22- Check Battery & CablesTest 21- Check 10 Amp Fuse Refer back to flow chart Test 23 Check Voltage at Starter Contactor SCTest 24 Check Starter Contactor SC Test 25 Check Starter MotorChecking the Pinion Tools for Starter Performance TestTest 26 Test Starter Contactor Relay SCR Set voltmeter to measure DC voltageTest 27 Check Start-Run-Stop Switch SW1 Test 28 Check Start-Run-Stop Switch SW1 WiringReconnect all wires to the switch Procedure Set voltmeter to measure resistanceTest 30 Check Spark Plugs Refer back to the Flow ChartTest 29 Check Ignition Spark Test 31 Remove Wire 18 / Shutdown Lead Refer to Flow ChartSSR and the Battery Charge Rectifier 2 BCR2 Test 32 Test Start Stop Relay SSRTest 33 Test Wire RUNMagnetos Test 34 Test Start Stop Relay WiringTest 35 Check and Adjust Ignition Test 36 Test Fuel Shutoff Solenoid FSS Test 37 Test Fuel Shutoff Solenoid VoltageTest 38 Check Fuel Pump MagnetoTest 39 Check Carburetion Test 40 Valve AdjustmentAdjusting Valve Clearance Adjust the regulated pressure on the gauge to 80 psi 52 Tightening the Jam NutTest 42 Check Oil Pressure Switch Wire Test 43 Check Start Stop Relay SSRTest 45 Check Wire 15 Circuit Test 46 Check Wire 14 CircuitTest 44 Test Starter Contactor Relay SCR Test 47 Check Fuel Shutoff SolenoidTest 50 Check Wire Test 49 Check Wire 15BTest 51 Check Wires 11S & 44S Test 48 Check HourmeterTest 52 Check Idle Control Switch Test 53 Check Idle Control WiringSW2 TB2Test 55 Check TR1 & TR2 Wiring Test 54 Check Idle Control Transformers ICTTest 56 Choke Test Continuity should be measuredMajor Disassembly Remove air deflector Figure B, Item #45 from cross memberSupport Alternator 3317 3026 20 22 25 QTY Description Detail of Battery Tray QTY. Description ELECTRICAL DATA RED Battery Charge Winding BA Brush Assembly Governor Actuator 167 229 15B Power Winding DPE Winding SCR Wiring Diagram 17.5 kW Drawing No G0731 Stator Closest to Bearing Electrical Schematic 17.5 kW Drawing No G0733 Circuit 11 ORG Circuit 13 DRK BLU Circuit 15 PNK ELECTRICAL DATA Page Frequency Hz 238-242 59-61 100 Rated Max DC Load Amperes Current @ 12 VoltsLoad % Torque Specifications Trim Torque SpecificationsPO BOX 297 WHITEWATER, WI

5308, 4583, 4451 & 4986, 4582 & 4987 specifications

Guardian Technologies has carved a niche in the market with its innovative air purification and UV-C sanitization products. The company's model numbers, including 4582, 4987, 4451, 4986, 4583, and 5308, represent a diverse range of solutions designed to enhance indoor air quality and safety in both residential and commercial settings.

The Guardian Technologies 4582 is equipped with a true HEPA filter that captures 99.97% of dust, pollen, smoke, and other particles as small as 0.3 microns. This model features a smart sensor that adjusts the fan speed according to the air quality in real-time. The UV-C light technology integrated into this device works to eliminate viruses and bacteria, providing an additional layer of protection against airborne pathogens.

The 4987 model follows suit with similar advanced features but adds a sleek design ideal for modern interiors. With multiple speed settings and a night mode, the 4987 is perfect for bedrooms or quiet spaces. Its energy-efficient operation coupled with an indicator that signals filter replacement ensures that users maintain optimal performance effortlessly.

The Guardian Technologies 4451 and 4986 models are particularly notable for their enhanced capacity and filtration efficiency. Both units incorporate a three-in-one filtration system that includes a pre-filter, activated charcoal filter, and HEPA filter. With their strategic design, these models not only purify the air but also trap common household odors, making them a popular choice for families with pets.

The 4583 model stands out with a unique combination of design and functionality. It features a low-profile design, making it easy to fit into any space. Its UV-C light technology not only disinfects air but can also sanitize surfaces, bridging the gap between air purification and direct sanitation.

Finally, the Guardian Technologies 5308 caters to larger spaces, offering impressive air circulation and filtration capabilities. Equipped with a high-efficiency particulate air (HEPA) filter and a powerful fan, it effectively cleans larger areas while maintaining whisper-quiet operation.

In summary, Guardian Technologies’ products exemplify a commitment to improving air quality and promoting health through innovative technology. With features like HEPA filtration, UV-C sanitization, smart sensors, and sleek designs, consumers can choose from a range of models that best fit their needs, ensuring cleaner, safer indoor environments.
Top Page Image Contents