Garmin EVA-2082S/1220, 353 manual EC-declaration of conformity, Applies to Europe only

Page 40

TECHNICAL DATA

EC-declaration of conformity

(Applies to Europe only)

Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that the chain saws for forest service Husqvarna 346XP, 346XPG, 353, 353G, 346XP E-tech, 346XPG E-tech, 353 E-tech and 353G E-tech, Triobrake from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the requirements of the COUNCIL’S DIRECTIVES:

-of May 17, 2006 "relating to machinery" 2006/42/EC

-of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.

-of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.

For information relating to noise emissions, see the chapter Technical data. The following standards have been applied:

EN ISO 12100-2:2003, CISPR 12:2005, EN ISO 11681-1:2004

Notiﬁed body: 0404, SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has carried out EC type examination in accordance with the machinery directive’s (2006/42/EC) article 12, point 3b. The certiﬁcates for EC type examination in accordance with annex IX, have the numbers: 0404/09/2086 – 346XP TrioBrake, 346 XPG TrioBrake, 346XPG E-tech TrioBrake, 0404/09/2087 – 353 TrioBrake, 353G TrioBrake, 353G E-tech TrioBrake.

In addition, SMP, Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has certiﬁed conformity with annex V of the Council’s Directive of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. The certiﬁcates have the numbers: 01/161/002 – 346XP TrioBrake, 346XPG TrioBrake, 01/161/003 – 346XPG E-tech TrioBrake, 01/161/061 – 353 TrioBrake, 353G TrioBrake, 01/161/046 – 353G E-tech TrioBrake.

The supplied chain saw conforms to the example that underwent EC type examination.

Huskvarna December 29, 2009

Bengt Frögelius, Development director chainsaw R&D (Authorized representative for Husqvarna AB and responsible for technical documentation.)

40 – English

Image 40

Contents Operator′s manual Symbols on the machine KEY to SymbolsSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawMachine′s safety equipment Always use common sensePersonal protective equipment Chain brake and front hand guardGeneral Safety Precautions Chain catcher Throttle lockoutRight hand guard Stop switch Cutting equipmentVibration damping system MufﬂerCutting equipment designed to reduce kickback BarChain Injuries Some terms that describe the bar and chainSharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment Which could lead to serious, even fatal injuries Chain oilFilling with chain oil Checking chain lubricationNeedle bearing lubrication Checking wear on cutting equipmentAssembly Fitting the bar and chainFitting a spike bumper Working with the chainFuel Handling FuelFuel safety FuellingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsJam. Always stop the engine before cleaning Terms Basic cutting techniqueLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionWhat is kickback? How to avoid kickbackCutting the trunk into logs Carburettor adjustment MaintenanceGeneral Correctly adjusted carburettor High speed jet HChecking the brake trigger Checking the right-hand brake triggerImmediately Mufﬂer Replacement of broken recoil and drive disc springs StarterChanging a broken or worn starter cord Tensioning the recoil springAir ﬁlter Spark plugLubricating the bar tip sprocket Needle bearing lubricationAdjustment of the oil pump Air Injection centrifugal cleaningRunning when making adjustments Cooling systemElectrical carburettor heating Temperature 0C or colderWinter use Maintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain ﬁling and ﬁle gaugesApplies to Europe only EC-declaration of conformityEN ISO 12100-22003, Cispr 122005, EN ISO Page Page Page Original instructions 1153178-26