Euro-Pro V1730H owner manual Cleaning the Dust Container, Charging the Cordless Sweeper

CLEANING THE DUST CONTAINER

To achieve the best performance, empty the dust container after each use.

1. Pull the dust		3. Replace dust container on cordless
container straight		sweeper.
out from the side.		4. Periodically remove the brush cover on
		the front of the cordless sweeper and
(Fig. 6)
		remove any build up of lint, hair or fiber
Fig. 6		on the rotating brush. To remove the
2. Empty dust		cover - grip the cover from the bottom,
		pull out and
container contents.		upward until the
(Fig. 7) If desired-		cover unlocks
you may rinse with		from the side
water to clean the		slots and tabs
dust container –		located on the
but dry thoroughly	Fig. 7	top of the
		sweeper. (Fig. 8)	Fig. 8
before replacing on the sweeper.

CAUTION: Do not accidentally turn unit on while cleaning. Do not clean while unit is charging.

CHARGING THE CORDLESS SWEEPER

1.Connect the charger plug to the charging jack or hole on the back of the

sweeper. Plug the the charging adapter into the wall outlet. (120V., 60Hz.) Use only TechWorld Charger AD-1215-UL8. (Fig. 9)

2.This cordless sweeper is powered by Ni-Cd batteries. Before first use, they must be charged for a minimum of 24 hours.

3.When recharging the unit, the "On/Off" switch must be in the "OFF" position.

4.The charging light indicator on the top of the sweeper will flash to indicate that the sweeper is properly charging.

5.The charging indicator will light will stop flashing when the battery is fully charged.

6.To recharge, repeat step #1 above. ChargingFig. 9

times will vary depending upon the amount of usage between charging cycles.

Note: Your sweeper is highly advanced and has electronic controls that optimize the cleaning ability and durability of the sweeper. Please review the following instructions carefully to ensure that all features are utilized for best performance.

1.When charging the sweeper, the battery/charge indicator will flash until the unit is fully charged and then turn steady.

2.When running the unit, the battery indicator will start as solid green, change to solid orange when approximately 70% of the battery life is used, and blink orange when in need of charging. The sweeper will prevent the batteries from being deeply discharged and will indicate this by the battery indicator flashing, the headlights flashing, and the sweeper will stop operating. This is normal and all that needs done is to recharge the sweeper fully.

3.When recharging from being fully discharged, the unit must charge for 1 hour minimum before it’s electronics will allow the unit to operate again.

4.When the sweeper on/off switch is depressed the sweeper will slowly come up to speed. This is done to optimize the life of all components of the sweeper and is normal.

5.When first started, the sweeper will start in the highest speed “III” to prevent overloading the unit when starting on heavy carpets. Other speeds can then be selected by depressing the speed selector switch.

6.For best cleaning performance, use speed “I” (low) on hard surfaces, speed “II” (medium) on low carpets/rugs, and use speed “III” (high) on deeper carpets. These are guide lines and you will find the optimum speed settings for your surfaces and debris to be picked up through use and experience.

7.The sweeper will automatically try to maintain speeds on all surfaces. The unit may appear to be pulsing during use to maintain it’s speed, this is normal. If this occurs, please select the next highest speed to gain optimum performance.

8.To protect your sweeper and it’s components, the sweeper is provided with an electronic overload circuit. If something were to jam or overload the brush bar system, the units speed indicators will flash and the unit will stop operating, this is normal. If this occurs, please switch the unit off, clear the obstruction from the brush bar and then depress On/Off switch to start sweeper again.

NOTE: If, when you place the sweeper to recharge and the charging indicator light does NOT illuminate, then press the On/Off button once to turn the sweeper off. The charging indicator light should now light up.

NOTE: Peak performance may only be realized after the unit has been charged and discharged two (2) or three (3) times.

IMPORTANT: To maintain peak performance of your cordless sweeper, it is recommended that the unit be fully discharged, then completely re-charged at least once a month.

CAUTION

•Use only with the battery pack supplied with the unit. (Item # X9730)

•Do not attempt to remove the battery pack from the unit to charge it.

•Never attempt to throw the battery pack or unit into a fire or incinerate it.

•Do not attempt to remove or damage the battery casing.

•Battery must be recycled or disposed of in accordance with local regulations at the end of it's service life. Please consult your Yellow Pages or local recycling center for more information.

STORING THE CORDLESS SWEEPER

Your cordless sweeper may be stored by using the slot on the back of the upper handle and hanging it from a screw secured to a wall or other vertical surface. Use a #6 flat or pan head screw with the appropriate hardware for the surface that the sweeper will be mounted on, (i.e. gyproc). Allow the screw head to extend a approximately 3/16" from the mounting surface. Always empty your sweeper before hanging up for storage.

5 6