Marantz CDR631 Recording submenus, Text Memory Review/Erase Text Memory, Auto track increment

MENU MODE

The numbers between parentheses refer to the fold-out.

Text Memory Review/Erase Text Memory

The input text data of the disc is once saved in the text memory until finalizing the disc. When the text memory is full, will appear on the display and unable to add more text data. If you want to add more text data, you have to

finalize the text data for each disc in order to obtain memory space or erase the entire memory following the operation below.

1Stay in the stop mode. (No Operation)

2Press STORE/MENU (20, 77) on the deck or the remote control to enter Menu mode.

3Rotate REC LEVEL/SELECT (19) or press S (15, 74), T (16, 82) to select the TEXT VIEW submenu.

appears on the display.

4Press PUSH ENTER (19) or ENTER (78) to confirm.

5Rotate RECLEVEL/SELECT (19) or press S (15, 74), T (16, 82) to select the disc you wish to erase.

6Press PUSH ENTER (19) or ENTER (78) to confirm. appears on the display.

7Press the PUSH ENTER (19) or ENTER (78) to confirm the erasure of the text for that particular disc.

8Press STORE/MENU (20, 77) to return to the submenu or 9 (13, 81) to exit.

Note:

-If there are no discs in the memory, the message appears on the display.

-/may also appear when unfinalizing a CD-RW disc for which text was stored (see ‘UNFINALIZING CD-RW discs’ page 12.). The same action(s) should be taken in order to obtain memory space.

Recording submenus

3Rotate REC LEVEL/SELECT (19) or press S (15, 74), T (16, 82) to select the AUTO TRACK submenu.

appears on the display.

4Press PUSH ENTER (19) or ENTER (78) to confirm.

5 Select Auto track or by rotating REC LEVEL/ SELECT (19) or press S (15, 74), T (16, 82).

6Press PUSH ENTER (19) or ENTER (78) to confirm.

•	When	is selected, track numbers will be automati-
	cally incremented during recording.
•	When	is selected, you can number the recorded tracks
	yourself by press TR.INCR. (25) or TRACK INCR (67).

7Press STORE/MENU (20, 77) to store settings and re- turn to the submenu or 9 (13) to exit.

AUTO TRACK	ON
Source
CD/MD	Track increment based on user data of in
(with user data)	cominng siganl
DAT/DCC	Track increment based on user data of in
(with user data)	cominng siganl
Unknow	Track increment after silence gap of 2.7
(no user data)	seconds on incominng siganl
Analog	Track increment after silence gap of 2.7
	seconds on incominng siganl
No source	None
(no lock)

Note:

- Auto track is a function to switch increasing the track num- bers either automatically or manually. When Auto track is ON, there are two ways to activate the function.

-If a digital source has track information (Q-subcode) such as CD or MD, the track transition is automatically increased ac- cording to track information of the digital source.

-If an audio source is analog or digital without track informa- tion, silence gap is detected. When length of silence gap is more than 2.7 seconds, the auto track function is automati- cally activated at the point of 2.7 seconds just before A (- 35 dB) is detected. (See following figure below.)

ENGLISH

•When Auto Track is ON, track numbers will automatically be increase during the recording, also able to set Auto stop ON/ OFF.

•You can adjust the right and left volume balance during the recording.

Audio source signal

A (-35 dB)

B (-55 dB)

Silence gap

Auto track increment

1Stay in the stop mode. (No Operation)

2Press STORE/MENU (20, 77) on the deck or the remote control to enter Menu mode.

	2.7 sec
B is DETECTED	A is DETECTED
Track X	Track X+1

19