Dixon 966057501, SE 5225 KOH CE manual Hydraulic Pump, Fluid Change, Purging

Page 47

LUBRICATION

Hydraulic Pump

Fluid Change

This transaxle is designed with an external filter for ease of maintenance. To ensure constant fluid quality levels and longer life an oil filter change interval of every 200 hours is recommended.

The following procedure can be performed with the pump installed in the vehicle, and the vehicle on level ground. Apply the bypass valve and lock the vehicle parking brake.

1.Place an oil drain pan with a two gallon capacity beneath the oil filter. Remove the oil filter from the pump.

2.After the oil has drained, wipe the filter base surface off and apply a film of new oil to the gasket of the new replacement filter.

3.Install the new filter by hand, turn ¾ to one full turn after the filter gasket contacts the filter base surface.

4.Drain old oil filters of all free-flowing oil prior to disposal. Place used oil in appropriate containers and dispose of it in accordance with laws in your area.

5.Remove the cap from the pump’s expansion tank located on the vehicle frame.

6.Fill reservoir with SAE 10W30 oil to just above the MIN-ADD line on the reservoir. After purging, check levels and add oil if necessary.

7.Reinstall the tank cap by hand. Do not overtighten.

8.Proceed to the purge procedure.

Purging

Due to the effects air has on efficiency in hydrostatic drive applications, it is critical that it is purged from the system.

These purge procedures should be implemented any time a hydrostatic system has been opened to facilitate maintenance or any additional oil has been added to the system.

The resulting symptoms in hydrostatic systems may be:

•Noisy operation.

•Lack of power or drive after short term operation.

•High operation temperature and excessive expansion of oil.

Before starting, make sure the pump is at the proper oil level. If it is not, fill to the specifications outlined earlier.

2

3

1

8061-016

1.Pump filter

2.Pump reservoir

3.Fluid fill lines

Changing the hydraulic pump oil filter

The following procedures are best performed with the vehicle drive wheels off the ground, then repeated under normal operating conditions.

1.Disengage the brake if activated.

2.With the bypass valve open and the engine running at fast idle, slowly move the directional control in both forward and reverse directions (5 or 6 times). As air is purged from the unit, the oil level will drop.

3.With the bypass valve closed and the engine running, slowly move the directional control in both forward and reverse directions (5 to 6 times). Check the oil level, and add oil as required after stopping the engine.

4.It may be necessary to repeat Steps 2 and 3 until all the air is completely purged from the system. When the transaxle operates at normal noise levels and moves smoothly forward and reverse at normal speeds, then the transaxle is considered purged.

5.After the vehicle has been used two times, the oil level should be checked while the oil is cold and adjusted accordingly.

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Operator Manual Page Contents Page Introduction Manufacturing Number Good ServiceSymbols and decals Performing any General Operation SafetySafety Instructions Never take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline General Maintenance Risk of sparking Customer Responsibilities TransportRollover Protection system Rops Control Locations ControlsSteering Control Levers Throttle Control Blade SwitchParking Brake Fuses Ignition SwitchChoke Control Fuel Tank Always raise the deck to the highest position for transport Cutting Height AdjusterFuel Shut Off Valve Hour Meter Seat Adjustment LeverSteering TrainingStarting the Engine Before StartingPlace controls in neutral position To remove cables, reverse order Weak BatteryPositive + terminal on each battery, taking Care not to short against chassisRunning Ensure that no one is near mower when engaging blade switchOperating On Hills Mowing Tips Stopping the Engine Pump release valves Manually Moving UnitBefore After Year 250 500 MaintenanceMaintenance Schedule Daily Maintenance interval Least Hours Once EachDaily At least Maintenance interval Once Hours Each Always wear eye protection when around batteries BatteryCleaning battery and terminals Replacing batteryFuel Filter Safety SystemTire Pressures Deck Belt Deck belt installationBelts Belt removal Belt installationPump Belt Replacing pump belt Cutting Blades Blade replacementLeveling deck Adjusting the Mower DeckAnti-scalp rollers Caster Wheels CleaningUse protective glasses when cleaning and washing Removal and installation of caster wheelGeneral LubricationDeck Outer Spindle Front Wheel MountFront Wheel Bearings Deck SpindlePurging Hydraulic PumpFluid Change Troubleshooting Troubleshooting Winter Storage ServiceStorage Schematics Transmission Technical Data966057501 Engine Vibration Dimension965871801 Frame Torque Specifications AccessoriesZero Turn Ride-on Mower USA RequirementsCE Requirements Action Date, mtr reading, stamp, sign Service JournalDelivery Service After 5-8 Hours Hour ServicePerform the 25-hour service At Least Once Each Year Service Journal Service Journal Service Journal Page 115 248226R1 01/28/10

966057501, SE 5225 KOH CE specifications

The Dixon SE 5225 KOH CE,966057501 is an advanced piece of equipment designed for professionals seeking both power and efficiency in their operations. This model is recognized for its robust construction and innovative features, making it suitable for various applications in demanding environments.

One of the key highlights of the Dixon SE 5225 is its versatility. It is equipped with a powerful engine that delivers impressive performance, ensuring that tasks are completed efficiently and effectively. The machine is capable of handling heavy loads while maintaining stability, which is crucial for safety in operational settings.

The SE 5225 also incorporates advanced technologies that enhance its functionality. For instance, it features a state-of-the-art control system that allows for precise handling and monitoring. This ensures that users have complete command over the machine's operations, leading to increased productivity and reduced operational downtime. Additionally, the model boasts a user-friendly interface, making it accessible to operators with varying levels of expertise.

Another significant characteristic of the Dixon SE 5225 is its durability. Constructed with high-quality materials that resist wear and tear, this equipment is designed to withstand the rigors of daily use. The engineering behind the machine emphasizes not only strength but also ease of maintenance, ensuring that upkeep is straightforward and cost-effective.

Moreover, the SE 5225 is designed with safety in mind. It includes multiple safety features, such as emergency shut-off systems and protective enclosures, to minimize the risk of accidents. These aspects are crucial for operations where safety is a top priority.

In terms of efficiency, the SE 5225 excels with its fuel economy features, making it an environmentally friendly option without compromising on power. This aligns with the industry's growing emphasis on sustainable practices while maintaining the performance required for professional tasks.

In conclusion, the Dixon SE 5225 KOH CE,966057501 stands out as a reliable and efficient solution for those in need of heavy-duty equipment. Its blend of power, advanced technology, and safety features make it an ideal choice for professionals looking to enhance their operational capabilities and achieve superior results in various applications. Whether in construction, logistics, or any other demanding field, this model is engineered to deliver.
Top Page Image Contents