Dixon 5501 manual Final Preparation, Mower Deck Deflector

Page 15

FINAL PREPARATION

MOWER DECK DEFLECTOR:

Remove hair pin cotter (P/N 3072) from deflector pin (P/N 6402), remove pin. Position deflector (P/N 9264) on mower deck. Reinstall deflector pin and hair pin cotter.

BATTERY:

1. Remove battery from chassis.

2.Fill each cell with electrolyte (acid) to ring at bottom of fill cap.

3.Allow battery to sit for (1 0) minutes, re-check acid level and top off any cells that are low.

4.Trickle charge battery using a charger of less than (6) amps until all cells are gassing freely. Hydrometer readings may be taken, if desired.

5.Install permanent battery caps and wash any accumulated acid from battery before re-installation on chassis.

6.Observe proper battery polarity when re-connecting leads on chassis. Always connect positive lead first.

ENGINE SERVICE:

Final preparation of engine should be completed using engine service manual provided with mower.

INITIAL START AND HYDROSTAT TRANSMISSION CHECK:

1.Final hydrostat checks have been performed at the factory, however, it is necessary to check that the pressure relief bypass on each hydrostatic transmission is completely released before attempting to drive mower.

2.Each hydrostat has a bypass relief pin located at the rear of the hydrostatic unit. A bypass keeper is provided to allow the mower to be rolled around without complete servicing of the unit. To accomplish this, the bypass keeper springs must be positioned to depress the bypass relief pins. Remove bypass keeper springs prior to actual operation of the mower.

Page 12

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Page Important Read Carefully Index Safety Safety Reminders Read Carefully Before Operation Safety Reminders Dixon Limited Warranty Policy HYDRO-GEAR Models Specifications SET UP and Service Do not Tighten Securely Seat Assembly InstructionsSeat Assembly Instructions Upper Control Lever Installation Mower Deck Installation Mower Deck Leveling Procedure Mower Deck Deflector Final PreparationOperation Instructions Operation Instructions Care and Maintenance Model Procedure for Electric Clutch Adjustment Reverse procedure to re-install deck assembly Care and Maintenance ModelDrive System Adjustments Adjustment Points for T-BOX Belt Tension Forward Lever Stop Adjustment Chassis and Mower Deck Number of grease zerks used Cleaning the Mower Troubleshooting Drive System Electrical System Situation Causes Remedy Page Page Page Page Page Page Page ZTR 5501 Parts List 3669 Decal Caution 3322 ZTR 5501 Parts List ZTR 5501 Parts List Page Page FAX 316 251

5501 specifications

The Dixon 5501 is a versatile and robust device designed for both industrial and commercial applications. This model is renowned for its precision, durability, and advanced features, making it a popular choice among professionals in various industries.

One of the main features of the Dixon 5501 is its high-performance capability. It is equipped with an advanced processing unit that allows for swift data processing and operational efficiency. This ensures that users can execute tasks with minimal delay, which is critical in time-sensitive environments. The device’s user interface is intuitive, featuring a clear display and easy-to-navigate controls designed for user-friendliness, allowing operators to access a wide array of functions effortlessly.

In terms of connectivity, the Dixon 5501 stands out with its support for multiple communication protocols, including Bluetooth and Wi-Fi, making it easy to integrate into existing systems. This connectivity ensures that data transfer is seamless, enabling real-time monitoring and remote management. The capability to connect with various external devices enhances its functionality and adaptability in various operational settings.

Another key characteristic of the Dixon 5501 is its robust construction. Designed to withstand challenging environments, it features an IP-rated enclosure, making it resistant to dust and water ingress. This durability is crucial for users who operate in harsh conditions, ensuring the longevity and reliability of the device.

The Dixon 5501 also incorporates cutting-edge technology in terms of data handling and analysis capabilities. It has advanced analytics features that allow users to derive insights from collected data, supporting proactive decision-making processes. This is particularly valuable in sectors such as logistics, manufacturing, and environmental monitoring, where data-driven decisions are key to operational success.

Additionally, safety and compliance are significant aspects of the Dixon 5501. It adheres to rigorous industry standards and regulations, ensuring that users can trust the device for critical applications. The combination of safety features and robust technology makes it a reliable choice for businesses aiming to enhance productivity while maintaining high safety standards.

In summary, the Dixon 5501 is a powerful device characterized by its performance, connectivity, durability, and advanced analytical capabilities. These features make it an invaluable tool for professionals seeking efficiency and reliability in their operations.
Top Page Image Contents