Desa 076728K SAW Chain Tension Adjustment, Filling OIL Tank, Installing Automatic Chain Sharpener

Page 7

OWNER’S MANUAL

ASSEMBLY

Continued

INSTALLING AUTOMATIC CHAIN SHARPENER

(Fast Sharp Models Only)

1.Screw automatic chain sharpener into threaded hole.

2.Continue turning automatic chain sharpener until you hear five (5) clicks.

Automatic

Chain

Sharpener

PUSH

SHARPENTO

Figure 5 - Automatic Chain Sharpener (Fast Sharp Models Only)

SAW CHAIN

TENSION

ADJUSTMENT

WARNING: Unplug chain saw from power source before adjust- ing saw chain tension.

WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain.

WARNING: Maintain proper chain tension always. A loose chain will increase the risk of kickback. A loose chain may jump out of guide bar groove. This may injure operator and damage chain. A loose chain will cause chain, guide bar, and sprocket to wear rapidly.

Note: For pre-assembled models, the saw chain tension is properly set at factory. A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Follow steps below to readjust saw chain tension.

1.Before adjusting chain, make sure guide bar nuts are only finger tight (see Figure 3, page 6). Also make sure adjust- ing block is in oval adjusting hole on guide bar (see Figures 3 and 4, page 6).

2.Turn adjusting screw clockwise until all slack is out of chain (see Figure 6). Note: There should be no gap between side links of chain and bottom of guide bar (see Figure 7).

3.Wearing protective gloves, move chain around guide bar. Chain should move freely. If chain does not move freely, loosen chain by turning adjusting screw counterclockwise.

4.After chain tension is correct, tighten guide bar nuts firmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kickback. This can also damage saw. Note: A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Readjust chain tension.

Figure 6 - Turning Adjusting Screw

Guide Bar

Nuts

Guide Bar

Guide Bar

Correct

Gap Tension

Incorrect

Tension

Figure 7 - Saw Chain Adjustment

FILLING OIL TANK

1.Remove oil cap.

2.Fill oil tank with SAE #30 motor oil. Note: For temperatures below 30°F, use

SAE #10 oil. For temperatures above 75°F, use SAE #40 oil.

3.Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from tank.

4.Wipe off excess oil.

Note: It is normal for oil to seep when saw is not in use. Empty oil tank after each use to prevent see page.

105419

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Electric Chain SAW Before Operating SAW SafetyWhile Operating SAW Kickback Maintenance and Storage of Chain SAWKickback Safety Devices On This Saw Saw Maintenance and Kickback SafetyChain SAW Names and Terms Unpacking ProductSee Saw Chain Tension Adjustment, AssemblyFast Sharp Models Only SAW Chain Tension AdjustmentInstalling Automatic Chain Sharpener Filling OIL TankCutting with the Chain SAW Operating Chain SAWExtension Cords Oiling ChainBefore Felling a Tree Felling Procedure Felling NotchFelling a Tree Cutting Down a TreeLog Supported On One End Limbing a TreeBucking a LOG Entire Length Of Log On GroundLog Supported On Both Ends Trimming a Tree PruningCare of Guide BAR Cleaning and MaintenanceCleaning SAW Body Normal Guide Bar MaintenanceNon-Fast Sharp Model Sharpening Cutters Sharpening SAW ChainItems Needed to Sharpen Chain Filing Cutter Depth Gauges Replacing SAW ChainFast Sharp Model Storage TroubleshootingTechnical Service Service PublicationsParts Centrals Authorized Service CentersMaine ME IndianaIowa IA Kansas KSOklahoma OK NEW York NYNorth Dakota ND Ohio OH079963-02 Replacement Parts and Accessories077155 Adjusting Plate Assy 097570-01S Guide bar 091374S Chain 075752 Drive sprocketWarranty Service NON-WARRANTY Service Repair Service

100015, 075762J, 104316-04, 076702J, 076728K specifications

Desa 100089-01, 076728K, 100015, and 076702J, along with the model 104316-04, represent a significant advance in modern technology and design, showcasing innovative features suited for various applications. These models are part of a wider effort to integrate efficiency and performance in consumer products.

Starting with the Desa 100089-01, it stands out for its robust construction and user-friendly interface. This model is engineered with high-grade materials that enhance durability while ensuring a lightweight design, resulting in easy portability without compromising strength. The intuitive controls allow users to operate the device seamlessly, making it ideal for both novice and experienced users.

The 076728K model features advanced connectivity options, supporting both wired and wireless connections. This adaptability makes it versatile for integration into various environments, whether in the home or office. Moreover, it includes smart technology that allows users to monitor and control settings remotely through a dedicated app, thereby enhancing convenience and efficiency.

The 100015 model takes a unique approach to energy consumption. It is equipped with state-of-the-art energy-saving technology that minimizes power usage while maintaining high performance. This feature is particularly beneficial in reducing overall operational costs and promoting sustainability.

The 076702J incorporates cutting-edge safety features, ensuring that users can operate it without worries. With multiple fail-safes and automatic shut-off features, user safety is greatly prioritized. Additionally, this model is designed to operate quietly, making it an excellent choice for environments where noise reduction is essential.

Finally, the 104316-04 model excels in versatility. Its design caters to multiple functionalities, making it suitable for a range of tasks. The adaptability of this model allows users to switch between different modes quickly, enhancing productivity whether in a workspace or a recreational setting.

Overall, these models—Desa 100089-01, 076728K, 100015, 076702J, and 104316-04—showcase a commitment to quality and performance. With advanced features, innovative technologies, and a focus on user experience, they are well-equipped to meet the needs of today's consumers. Each model brings unique characteristics to the table, ensuring that there’s a suitable option for a diverse array of applications.
Top Page Image Contents