Section V Maintenance and Storage | Country Home Products TLC18-CHP

SECTION V - MAINTENANCE AND STORAGE

IMPORTANT: The knife should be checked for sharpness and the nuts and bolts attaching it to the flywheel for tightness every 8-10 hours of operation.

IMPORTANT: Every time you perform maintenance or any kind of service or check on the knife, be sure to check the gap between the knife and wear plate for proper setting.

NOTE: A knife gauge has been provided with your machine. It is 1/16th” thick and should be used to set the correct gap between the knife and wear plate.

If the cutting mechanism strikes any foreign object or if your machine should start making an unusual noise or is vibrating, stop the engine, disconnect both spark plug wires from the spark plugs. Allow the engine to cool before you;

a.Inspect and examine for obvious damage.

b.Check for loose parts, bolts, and nuts.

1.When not in use, your chipper should be stored out of the reach of children. Be sure there are no gasoline fumes in the storage area. For long periods of storage (over winter), refer to the engine owner’s manual.

2.After every 10 hours of operation, lubricate the chipper side and drive side bearings with multi-purpose lithium grease. Also, check the bearing collar set screws regularly to be sure they are tight. If they are loose, reset them with Loctite 243, obtainable at any hardware store.

3.You will find information included referring to operation and maintenance of the chipper engine. Look it over carefully. BE CERTAIN TO SERVICE THE ENGINE BEFORE YOU START IT.

4.When the steel chipping knife (item #11, pg. 33) needs replacing or sharpening, refer to the section on removal, sharpening and re-installation.

5.Care must be exercised when sharpening the knife to maintain the correct bevel and a straight edge. Refer to sharpening directions. When you install a knife, the clearance between the knife and wear plate must be checked and set. This clearance or gap should be set to 1/16” (see figure 1).

6.To adjust this clearance, loosen the three ¼” nuts and bolts (item #16 & #22, pg. 33) holding the wear plate in place. The wear plate can be slid up or down (in or out) to achieve the correct gap setting.

7.Take the knife gauge and slide between the knife and wear plate. If the gap is set correctly, the knife gauge will lightly touch both the knife and wear plate. If the gap is too small, you will not be able to get the gauge between the knife and wear plate. If the gap is too large, there will be excess room between knife gauge, knife and wear plate. Tighten the nuts and bolts when the wear plate is in the correct position. Be certain the flywheel rotates without hitting anything before starting the chipper.

8.If the gap between the wear plate and the knife is not set correctly, you will have excessive vibration when chipping and the blade will seem to be dull. This should be checked every 8-10 hours of operation.

9.If at any time it becomes necessary to disassemble the chipper for repairs, the chipper disk (item #13, pg. 33) must be re-installed in exactly the same position on the rotor shaft.

NOTE: Proper gap setting is critical to the proper operation of your machine.

TLC18-CHP specifications

Country Home Products has established itself as a leader in the outdoor power equipment industry, and one of its standout offerings is the TLC18-CHP, a versatile and powerful tiller designed for home gardeners and professional landscapers alike. The TLC18-CHP is engineered with cutting-edge technology and features that make soil preparation easier and more efficient.

At the heart of the TLC18-CHP is a robust engine that provides reliable power for tilling. With a powerful 6.5 horsepower engine, this tiller can easily break up the toughest soil and manage weeds effectively. The engine is designed for optimal fuel efficiency, ensuring that users can till larger areas without the need for frequent refueling.

One of the most notable features of the TLC18-CHP is its innovative dual-tine design. This design not only improves the tilling depth but also enhances the overall efficiency of the tilling process. The heavy-duty tines are capable of penetrating hard soil, ensuring that users can create a well-aerated and nutrient-rich seedbed. The variable tilling width allows for personalized control, making it versatile enough for gardens of all sizes.

The tiller is equipped with an easy-to-use throttle control and a user-friendly handle that can be adjusted for height, allowing for comfortable operation regardless of the user's stature. This ergonomic design reduces fatigue during extended use, making it ideal for large gardening projects.

Safety has not been overlooked in the TLC18-CHP's design. It features safety shields and reinforced components to protect the operator during use. The inclusion of a reliable anti-vibration system minimizes hand and arm discomfort, offering an enhanced user experience over prolonged periods.

Another important aspect of the TLC18-CHP is its durability. Constructed with high-quality materials, it is designed to withstand harsh outdoor conditions. The easy-to-maintain components ensure that users can spend more time working in their gardens and less time worrying about equipment maintenance.

In summary, the Country Home Products TLC18-CHP is a powerful, versatile, and user-friendly tiller that meets the needs of both amateur gardeners and professionals. With its advanced technologies, ergonomic design, and robust construction, it is indeed a valuable addition to any outdoor equipment arsenal, promising to make tilling tasks more efficient and enjoyable.