Bush Hog Estate Series manual Deck Belt Replacement, Deck Belt Diagram

Page 18

LEVELING THE DECK AND SETTING THE

DECK BELT ADJUSTMENT

COUNTERBALANCE SPRING TENSION

Belt adjustment should be checked every (50) hours

 

 

1.

Set all tire pressures to the correct specifications.

of operation to get maximum life and cutting perfor-

mance. Belt tension is adjusted by increasing or

2.

Rest machine on a level slab of concrete.

decreasing the length of the spring on the movable

3.

Depress the deck lift pedal to raise the deck to the

idler by adjusting the eye bolt length (Shown below).

 

full lift height position and move the height adjust

 

For correct belt tension, adjust the spring length to 6-

 

pin to the 4.5” position.

 

7/8” for the 44” deck and 7-1/2” for the 52” deck.

4.

Take all the force off the two deck lift springs by

 

 

loosening the nut at the front of each spring.

DECK BELT REPLACEMENT

5.

Place a level on the deck, from front to rear. If the

 

level is too short to reach all the way from front to

(NOTE: Use only genuine Bush Hog

 

rear, lay a straight edge on the deck first, then

replacement parts)

 

place the level on the straight edge.

 

6.

Lay a .12” spacer beneath the front level. this will

1. Remove the R.H. and L.H. deck shield assemblies

 

automatically set the rear of the deck higher than

(Fig. ).

 

the front.

2. Relieve the spring tension by loosening the two

7.

Adjust the nuts at the rear trunnion forward to

5/16” hex nuts on the spring adjustment eye bolt.

 

raise the rear of the deck (Shown below) until the

3. Remove the old belt.

 

level’s bubble is centered. Repeat for the other side.

4. Install the new belt being sure the belt is properly

8.

Check to verify the deck is leveled side-to-side. To

routed and positioned in all sheave grooves.

 

do this, lay a 2” x 4” x 30” piece of wood under

5. Adjust tension on the belt by adjusting the length

 

each side of the deck and lower the deck to rest

of the spring on the idler (See Deck Belt

 

freely on the top of these boards. Inspect the (4)

Adjustment section).

 

lift chains to see if tension is on each of them. If

6. Replace the deck shield assemblies.

 

any of the chains appear slack, loosen the cam

DECK BELT DIAGRAM

 

bushing bolt just enough to allow the cam bushing

 

to be turned to remove the slack from the chain.

Spring Length

 

Tighten the cam bushing bolt to 76 ft.lbs.

44” Deck - 6-7/8”, 52” Deck - 7-1/2”

9.Raise the deck up to the transport position and lock in place.

10. Remove the 2” x 4”s from under the deck.

Eye Bolt Adjustment

11. Tighten each of the counterbalance spring nuts

 

until springs are to the following lengths.

 

44” Deck - Spring length of 16.5”

 

52” Deck - Spring length of 16.0”

 

The springs may be tightened or loosened from

 

this point according to personal preference.

 

Rear Trunnion

Spring Loaded Idler

 

Level on

 

Mower Deck

 

.12” Spacer

 

At Front End

 

Height

 

Adjustment Pin

 

Deck

WARNING

Lift Pedal

TO AVOID SERIOUS BURN INJURIES:

Upper

● ALLOW ENGINE, OIL AND HYDRAULIC FLU-

Chain Fastener

IDS TO COOL BEFORE SERVICING TRANSMIS-

 

Deck

SION OR ENGINE SYSTEM

Shield

CAUTION

Deck

TO AVOID CLEANING SOLVENT FIRES:

 

Deck Lift Spring

● AVOID USING FLAMMABLE SOLVENTS.

● AVOID AREAS WITH IGNITION SOURCES

Adjustment Nut

WHEN USING FLAMMABLE SOLVENTS.

 

16

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Bush HOG Congratulations Table of Contents Retail CUSTOMER’S Responsibility Under the Bush HOG WarrantyThis Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List Estate Series Zero Turn RiderSafety Alert Symbol Your Safety is InvolvedImportant Safety Precautions Safety Instructions and RecommendationsAccident Patterns to Avoid Never Carry Passengers Do not USE Mower When Grass is WET or Slippery Section Introduction and Description IntroductionDescription Controls Tractor SpecificationsDeck Specifications Operator Interlock SystemSection Operation General SafetyPRE-OPERATION Checklist OperationCutting Height Adjustment ANTI-SCALP Roller AdjustmentOperation on Slopes Mowing Recommendations Hr break-in Grease blade spindles every 50 hours Section MaintenanceMaintenance Schedule Important Substitution of an improper filter will causeTires BatteryEngine Mower BladesNeutral Adjustment Control Lever AdjustmentCleaning Grass Build UP Under Deck Deck Belt Replacement Deck Belt DiagramSTART-UP Maintenance Hydrostatic Transaxle Belt Tension AdjustmentHydrostatic Transaxle Motion Drive Belt Replacement Fluid Volume and LevelPurging Procedures Parking Brake AdjustmentTroubleshooting Check List Section IV Assembly Safety Decals To Avoid Serious Injury or Death50043277 50012615 94131 50043279 50043280 Torque Specifications Recommended Torque in Foot Pounds Newton MetersBush HOG, L.L.C

Estate Series specifications

Bush Hog Estate Series is an impressive lineup of versatile and durable lawn and garden equipment designed to cater to a variety of landscaping tasks. Recognized for their robust performance, these machines are built with homeowners and professionals in mind who require reliable and efficient tools for yard maintenance and improvement.

One of the standout features of the Estate Series is its powerful engine options, providing ample horsepower to handle various conditions and terrains. Whether you're tackling tough grass, dense brush, or uneven ground, the efficient engines ensure that users experience consistent performance. Moreover, the series often comes equipped with reliable hydraulic systems that improve lifting and towing capabilities, which are essential for managing heavy loads and attachments.

The build quality of the Bush Hog Estate Series is another major highlight. Constructed with high-grade materials, these machines offer great resilience against wear and tear, ensuring they can withstand the rigors of everyday use. The heavy-duty frames and reinforced structures contribute to the longevity of the machinery, making it a smart investment for both homeowner and professional use.

Ease of use is a core principle embedded in the design of the Estate Series. Many models come with intuitive controls that facilitate effortless operation, allowing users to focus on their tasks without being hindered by complicated machinery. Additionally, features such as adjustable cutting heights and easy-to-maneuver designs make these tools adaptable for various landscaping projects.

Safety is also prioritized in the Bush Hog Estate Series. With features such as roll-over protection systems and secure operator platforms, users can confidently operate these machines. The design minimizes potential hazards, making it easier for users to focus on their tasks without unnecessary risk.

One cannot overlook the innovative technologies integrated within the Estate Series. The machines often incorporate advanced drive systems that enhance traction and maneuverability, crucial for maintaining stability in challenging terrains. Furthermore, some models may include options for GPS guidance systems, enabling precision in landscaping and mowing tasks.

In summary, the Bush Hog Estate Series stands out due to its powerful performance, durable construction, user-friendly operation, and enhanced safety features. The combination of these characteristics and advanced technologies makes it an excellent choice for anyone looking to invest in reliable lawn care equipment. With the Bush Hog Estate Series, achieving a well-maintained lawn and garden has never been easier.
Top Page Image Contents