Bush Hog Commercial Series manual Operation, Cutting Height Adjustment Decal, Cauton

Page 14

OPERATION

1.OPEN FUEL TANK SELECTOR VALVE left or right tank.

2.MOVE CONTROL LEVERS TO neutral “OUT” position by pushing each one straight sideways.

3.SET PARKING BRAKE. Pull rearward to set.

4.DISENGAGE MOWER BLADE CLUTCH by moving clutch switch to “OFF” (down) position.

5.SET ENGINE CHOKE CONTROL for cold starts to full position.

6.SET ENGINE THROTTLE TO 1/2 throttle.

7.TURN IGNITION KEY to “START” position and release to “RUN” as soon as engine starts. NOTE: Prolonged cranking will damage starter motor and shorten the battery life.

8.ADJUST ENGINE THROTTLE AND CHOKE for desired engine smoothness and speed. NOTE: When mowing, always run engine at full throttle.

9.RELEASE PARKING BRAKE. Push brake lever forward to release.

CAUTON

If the operator is inexperienced with the zero turn mower lever steering/speed control, he/she should follow these recommendations: Disengage the mower blades. Go very slowly until thoroughly familiar with the machine. Keep away from fences, buildings, and other obstruc- tions. While becoming familiar with the machine, move the Control Levers smoothly and slowly. Practice until operation is smooth and efficient.

10.A roll-over protection system (ROPS) is installed on your machine. Operate unit with the ROPS in the raised and locked position and use seat belt. There is no roll-over protection when the ROPS is down. If it is necessary to lower the ROPS, do not wear seat belt. Raise the ROPS as soon as clearance permits.

WARNING

MAKE SURE SEAT FRAME RETENTION CLICK-PINS ARE IN PLACE AFTER LIFT- ING SEAT PAN FOR SERVICE.

11.TO DRIVE: Adjust seat forward or backward for operator comfort. Move the Control Levers to the “IN” position. Move Control Levers forward to move forward. Move levers slowly forward to increase speed. To reverse direction, move the Control Lever on the side to which you want to turn slightly rearward of the other Control Lever. To turn on a zero radius axis, go slowly and pull one Control Lever back and push the other

Control Lever forward, depending on which direction you wish to turn.

WARNING

AVOID SERIOUS INJURY OR DEATH:

DO NOT MOVE STEERING LEVERS FROM FORWARD TO REVERSE OR REVERSE TO FORWARD POSITION RAPIDLY. A SUDDEN CHANGE IN DIRECTION MAY CAUSE LOSS OF CONTROL AND/OR DAMAGE TO EQUIPMENT. FOR SMOOTH, SAFE OPERATION, MOVE THE CONTROL LEVERS IN A GENTLE, SLOW MOTION, ESPECIALLY ON GRADES.

12.BRAKING: To brake mower, gently move Control Levers in the direction opposite to travel. If the parking brake is engaged with the Control Levers in the “IN” position the engine will stop.

13.CUTTING HEIGHT ADJUSTMENT:

1.Stop engine and move the control levers to the neutral position and engage the parking brake.

2.Disengage the blades.

3.Depress the deck lift foot pedal raising the deck to the transport position and place the pedal in the locked position.

4.Insert height adjustment pin into the hole cor- responding to the desired cutting height. See decal on the side of the deck lift plate.

5.Depress the deck lift pedal and lower the deck to the selected mowing height.

6.To transport, depress the lift foot pedal and lock in position, then move the height adjustment pin to the 5” position.

7.The cutting height adjustment is only a recom- mended guide. During normal mowing cut only 1/3 of the grass blade. Set cutting height to achieve your desired results.

CUTTING HEIGHT ADJUSTMENT DECAL

12

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Bush HOG Congratulations Table of Contents Retail CUSTOMER’S Responsibility Under the Bush HOG WarrantyThis Limited Warranty Shall not Apply Disclaimer of Implied Warranties & Consequential DamagesDealer Preparation Check List Commercial Zero Turn Riding MowerSafety Alert Symbol Your Safety is InvolvedImportant Safety Precautions Accident Patterns to AvoidSafety Never Carry PassengersTowing Slope OperationOsha Regulations EMPLOYERS, Employees and OperationsThis Act Seeks Child Labor Under 16 Years OldDescription Section Introduction and DescriptionIntroduction Controls Tractor SpecificationsDeck Specifications Operator Interlock SystemSection Operation General SafetyPRE-OPERATION Checklist Do not mix oil with gasolineOperation Cutting Height Adjustment DecalCutting Height Adjustment CautonANTI-SCALP Roller or Caster Adjustment ANTI-SCALP RollerMowing Recommendations Hr break-in Grease blade spindles every 50 hours Section MaintenanceMaintenance Schedule Important Substitution of an improper filter will causeTighten retaining bolt to 76 ft./lbs Motion Control Steering Adjustment Drive AdjustmentsMotion Control Lever Adjustment Stop the Engine Before Making AdjustmentsLeveling the Deck Deck Belt AdjustmentDeck Spindle Belt Routing Diagram Counterbalance SpringHydrostatic Maintenance START-UP MaintenanceSTART-UP Procedure Parking Brake AdjustmentTroubleshooting Check List Section IV Assembly Kawasaki Engine Wiring Harness Kohler Engine Wiring Harness Safety Decals Rotating Drive Parts BeneathTo Avoid Serious Injury or Death Torque Specifications Recommended Torque in Foot Pounds Newton MetersOptional Equipment Slope Angle Guide Fold Along Appropriate Line

Commercial Series specifications

Bush Hog has long been synonymous with durability and efficiency in agricultural equipment, and the Bush Hog Commercial Series takes that reputation to the next level. Designed for professionals in the landscaping, agriculture, and construction sectors, this series offers innovative features and advanced technologies that ensure high performance and reliability in tough working conditions.

At the heart of the Bush Hog Commercial Series is its robust construction. Each model is built with heavy-duty materials to withstand the challenges of demanding environments. Whether you are mowing large fields or tackling tough brush, these machines are engineered to provide consistent results day after day. The reinforced decks and frames are designed to minimize wear and tear, extending the lifespan of the equipment and enhancing its resale value.

One standout characteristic of the Commercial Series is the engineering that goes into its cutting systems. The unique blade design delivers a superior cut while reducing the amount of horsepower required, making the machines more efficient and fuel-efficient. The patented blade technology also ensures smooth operation, minimizing downtime from maintenance.

Furthermore, the Bush Hog Commercial Series incorporates advanced technology for added convenience and safety. Features such as adjustable cutting heights provide users with the flexibility needed to adapt to various terrain and vegetation types. Electric lift options help reduce operator fatigue during extended use, while the ergonomic design of the controls ensures ease of operation.

The series is also equipped with user-friendly maintenance features. Quick-access grease points and a simplified belt system service allow operators to spend less time on upkeep and more time getting work done. This focus on easy maintenance is part of Bush Hog's commitment to keeping your equipment running smoothly and efficiently.

In terms of performance, the Commercial Series units are powered by reliable engines that deliver strong torque and speed, allowing for quick job completion without sacrificing quality. The rugged tires provide excellent traction, enabling these machines to navigate various terrains with ease.

In conclusion, the Bush Hog Commercial Series stands out in the marketplace for its combination of durability, performance, and advanced engineering. With a suite of features tailored for professionals, this series promises to meet the rigors of any landscape, construction, or agricultural project, allowing operators to achieve optimal results while enjoying the benefits of high-quality equipment. Whether users need to maintain pristine lawns or clear overgrown brush, the Bush Hog Commercial Series is ready to rise to the occasion.
Top Page Image Contents