Starting, Cutting Operation, Blade Clutch

16OPERATION

INTENDED USE: This is not a lawn mower. The BC2401 is designed for cutting overgrown weeds, brush, and other types of organic growth to a height of 3-1/2". The unit may also be used to clear small saplings 1-1/2" in dia. or less. It does not provide the cut quality of a finish cut lawn mower. The unit is designed for use in rural areas, and should not be used in settings where conditions require that the unit be operated in tight or confined areas. Be sure to inspect work area and machine before operating. Make sure that all operators of this equipment are trained in general machine use and safety.

Like all mechanical tools, reasonable care must

be used when operating machine. Do not operate unit in areas where bystanders may be present.

Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for damaged or worn blade, loose blade bolt, loose blade adapter key, loose engine or lodged foreign objects. Note: See parts list for proper blade bolt torque specifications. (See trouble shooting section on page 12).

16.1STARTING

PUT OIL IN ENGINE BEFORE STARTING.

ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used.

Engine must be level when checking and filling oil and gasoline.

ENGINE SPEED: Controlled by throttle lever on the handle.

FUEL VALVE: Move fuel valve to "ON" position (when provided on engine).

CHOKE:

Briggs engines have a choke type carburetor that is operated by moving the throttle control to the full start position.

Honda engines have a separate choke lever that is oper- ated by pulling back when starting. Push it back to its original position after the engine has started.

THROTTLE: Move remote throttle control to fast position. Pull starting rope to start engine.

ELECTRIC START: Choke the engine if necessary. Push and hole down on the rocker switch until engine starts, then release switch to run.

IF YOUR UNIT FAILS TO START:

See Troubleshooting on page 12.

NOTE: Do not engage blade during transport between work sites. The blade should remain disengaged at all times when work is not being performed.

The best performance is achieved when cutting in dry conditions. If the deck becomes choked with grass or debris during operation, back unit off of debris allowing machine to clear itself and continue cutting, or shut the unit off and clear the clog by hand (See below). A drop in engine RPM or a notice- able change in engine sound is usually a good indicator of a clogged discharge or other interference.

Under most conditions cutting should be done in first or second gear. Third gear should be reserved for conditions where weeds and brush are thinned out or not as tall. The quality of the cut produced is directly related to the unit's ground speed during cutting. If the quality of the cut is not satisfactory (i.e. material left standing) you should shift into a lower gear during cutting. For improved control in confined areas, this machine can be pushed forward or backward by releasing the operator's clutch lever, placing the transaxle in neutral, and pushing the machine.

CLEARING A CLOGGED CUTTING DECK:

Turn engine off and wait for blade to stop completely. Disconnect spark plug wire. Wearing durable gloves, remove clog.

Danger, the clog may contain sharp materials. Reconnect spark plug wire.

BLADE CLUTCH

The Brush Cutter blade clutch is controlled by an operator presence control. To engage the blade, depress the operator's left hand control lever against operator's handle. The blade is disengaged by releasing this lever.(See Fig. 1.1)

NOTE: The blade clutch must be either fully engaged for cutting or fully disengaged to bring the blade to a stop. Do not operate the unit with the blade clutch partially engaged. Premature belt wear and clutch failure will result from improper operation of the clutch.

CAUTION: Use extreme care when operating the blade. Inspect the work area for foriegn objects that could cause damage to the unit or injure the operator if struck by the blade. Never operate the blade with bystanders in the work area.

	Lever Up
	Disengages
Handle	Clutch
	Lever

16.2 CUTTING OPERATION

GENERAL OPERATION: To engage the blade, depress the operator's left hand control lever against operator's handle. The blade is disengaged by releasing this lever.(See Fig. 1.1)

To engage the wheel drive, lift the operator's right hand

control lever against operator's handle. The drive is disen-
gaged by releasing this lever.(See Fig. 1.2) Ground speed can
be varied by shifting gears as described on page 9. To begin
cutting engage the blade lever, allow the blade to spin up to
speed, and engage the wheel drive to begin moving forward
into the material to be cut.	Fig. 1.1

Lever

Down

Engages

Clutch

Part No. 500264

Page 5 of 12

Form No. F051903A

BC2402HE, BC2401IC, BC2402H specifications

The Billy Goat BC2402H, BC2401IC, and BC2402HE are part of Billy Goat's impressive lineup of brush mowers designed for superior performance and reliability, making them ideal for both commercial and residential use. Each model, though distinct, shares core features and innovations that elevate their capabilities in tackling tough overgrown terrains.

The BC2402H is equipped with a robust Honda engine, providing reliable power and enhanced performance. This model features a heavy-duty, all-steel construction that ensures durability even in challenging conditions. Its 24-inch cutting deck, along with a dual-blade system, allows for efficient cutting and mulching, significantly reducing the time needed to clear large areas. The BC2402H also boasts a self-propelled drive system with variable speed, enabling operators to adjust the speed according to the terrain, thereby enhancing maneuverability.

Moving on to the BC2401IC, this model distinguishes itself with its innovative control features, designed for ease of use. The integrated control system allows for smooth operation, providing users with better handling and reduced fatigue during extended periods of use. Its lightweight design makes it easy to maneuver in tight spaces while still delivering the robust cutting power required for thick brush and weeds. The BC2401IC retains the signature Billy Goat durability, constructed to withstand the rigors of heavy-duty landscaping tasks.

The BC2402HE is a step further in technology and efficiency, featuring enhanced ergonomics and a powerful engine that ensures top-tier performance. This model focuses on user comfort, incorporating an adjustable handle and vibration dampening technology, which minimizes operator fatigue during lengthy jobs. The BC2402HE also excels in versatility, with adjustable height settings that accommodate various cutting needs, allowing for everything from fine trimming to tackling dense undergrowth.

In summary, the Billy Goat BC2402H, BC2401IC, and BC2402HE represent the pinnacle of brush mowing technology. With powerful engines, durable construction, and user-friendly features, these models are designed to meet the demands of both professional landscapers and homeowners. Their ability to efficiently clear overgrown areas while providing optimal comfort and control makes them indispensable tools for anyone looking to maintain their outdoor spaces effectively. Whether you’re dealing with thick brush or just need regular lawn maintenance, these models offer the solutions you need to get the job done right.