Billy Goat KD510SP, TKD510SP Starting, Use caution when using chipper, Clearing a Clogged Nozzle

Page 5

16Operation

INTENDED USE: This machine is designed for vacuuming leaves, grass clippings and other types of organic litter and for chipping brush, limbs, corn and sunflower stalks and palm fronds.

Debris mixed with cans, bottles and small amounts of sand can be vacuumed; however, it is not this machine's primary purpose. Vacuuming cans, bottles and sand will affect the longevity of your machine.

Do not operate if excessive vibration occurs. If excessive vibration occurs, shut engine off immediately and check for damaged or worn impeller, loose impeller bolt, loose impeller key, loose engine or lodged foreign objects. Note: See parts list for proper impeller bolt torque specifications. (See trouble shooting section on page 12).

Like all mechanical tools, reasonable care must be used when operating machine.

16.7CHIPPING OPERATION

(TKD MODLES ONLY)

Wearing Eye Protection and Durable Gloves is recommended while operating chipper.

Use caution when using chipper

Your TERMITE ® chipper is designed to process tree branches and limbs up to 2" (50.8mm) diameter.

Inspect machine work area and machine before operat- ing. Make sure that all operators of this equipment are trained in general machine use and safety.

PUT OIL IN ENGINE BEFORE STARTING.

2

(50.8 mm) Maximum Diameter

16.1STARTING

ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used.

Engine must be level when checking and filling oil and gasoline.

ENGINE SPEED: Controlled by throttle lever on the handle. Under normal conditions, operate at minimum throttle to accomplish your current cleaning task.

FUEL VALVE: Move fuel valve to "ON" position (when provided on engine).

CHOKE: Operated with throttle control (Honda only).

PRIMER: Push primer per engine instructions ( B&S only).

THROTTLE: Move remote throttle control to fast position. Pull starting rope to start engine.

IF YOUR UNIT FAILS TO START:

See Troubleshooting on page 12.

16.2VACUUMING OPERATION

VACUUM NOZZLE HEIGHT ADJUSTMENT: is raised and lowered by pulling slightly upward on handle and pulling height adjust rod (item 23) up at left rear of machine.

FOR MAXIMUM PICKUP: Adjust nozzle close to

debris, but without blocking airflow into the nozzle. NOTE: Never bury nozzle into debris.

CLEARING A CLOGGED NOZZLE

&EXHAUST: Turn engine off and wait for impeller to stop completely and disconnect spark plug wire. Wearing durable gloves, remove clog. Danger, the clog may contain sharp materials. Reconnect spark plug wire.

Several small branches can be grouped together and fed together into the chipper (see fig 2.).

When feeding forked branches, squeeze forks together and feed into chipper entrance (DO NOT overload). If forks are too large, use a pair of loppers to trim forks down to size. A lopper storage bracket is provided on every unit (loppers are not included)

16.8CLEARING A CLOGGED CHIPPER HOPPER-TKD ONLY

Under normal circumstances, allow time for machine to clear all wood from chipper hopper before stopping

engine. Otherwise, remaining pieces of wood will jam inside of chipper when engine stops. (See Tamper page 7).

Disconnect spark plug wire.

Remove debris bag quick disconnect from debris outlet on machine.

Wearing durable gloves, access impeller through debris outlet on fan housing and rotate impeller counter clock wise to dislodge and remove jam and

remove debris from hopper with tongs or equivalent. Reconnect debris bag quick disconnect to machine. Reconnect spark plug wire.

Part No. 890424

Page 5 of 12

Form No. F011398A

Image 5
Contents Hose Kits Shredder KITNozzle Wear Plates Standard Turf Quick Debris BAGVibration SoundPUT OIL in Engine Before Starting Packing ChecklistControls Literature Assy P/NStarting Use caution when using chipperClearing a Clogged Nozzle TKD Modles onlyCompost MulchEngine Debris bags are normal replaceable wear itemsPropulsion TAMPER-TKD only Handling &TRANSPORTINGStorage Impeller Removal Disconnect Spark Plug Wire Before Servicing UnitDebris BAG See Chain Replacement Chain AdjustmentsClutch Adjustment Impeller RemovalParts Drawing KD510SP Parts List TroubleshootingEngine Service and Warranty LpA