Ariens 915163 ZOOM XL 42 PTO or mower, Blades do not, Off, Engine, Overheats, Unit moves with

Page 29

PROBLEM

PROBABLE CAUSE

 

CORRECTION

 

 

 

 

 

PTO or mower

1.

Operator presence

1.

Depress operator presence switch

blades do not

 

switch not

 

by sitting on seat.

engage or shuts

 

depressed.

 

 

off.

2.

Faulty operator

2.

Contact your AriensDealer.

 

 

 

presence switch.

 

 

 

3.

Electric clutch

3.

Connect the electric clutch

 

 

connector is loose

 

connector. See REPLACING

 

 

or disconnected.

 

HYDROSTATIC BELT on page 25

 

 

 

 

for the electric clutch connector

 

 

 

 

location.

 

4.

Faulty PTO belt.

4.

Replace PTO belt (see REPLACING

 

 

 

 

PTO BELT on page 24).

 

5.

Faulty PTO switch,

5.

Contact your Ariens Dealer.

 

 

wires, connectors,

 

 

 

 

or clutch.

 

 

 

 

 

 

 

Engine

1.

Engine oil level

1.

Add engine oil. Refer to Engine

overheats.

 

low.

 

Manual for detailed instructions.

 

2.

Cooling system

2.

Clean cooling system. Refer to

 

 

plugged.

 

Engine Manual for detailed

 

 

 

 

instructions.

 

3.

Faulty engine.

3.

Contact your Ariens Dealer.

 

 

 

 

 

Unit moves with

1.

The parking brake

1.

Contact your Ariens Dealer.

engine off and

 

needs adjustment.

 

 

parking brake

2.

Faulty parking

2.

Contact your Ariens Dealer.

engaged.

 

 

brake.

 

 

 

 

 

 

 

Hour meter

1.

Ignition key is in

1.

Turn ignition key to the off position.

continues when

 

the run position

 

 

engine not

 

with engine turned

 

 

running.

 

off.

 

 

 

 

 

 

 

 

 

 

 

Unit does not

1.

Incorrect tire

1.

Check tire pressure (see

travel in a

 

pressure.

 

SPECIFICATIONS on page 31)

straight line.

2.

Steering levers

2.

Adjust steering levers (see Forward

 

 

 

need adjustment.

 

and Reverse Speed Adjustment on

 

 

 

 

page 23)

 

3.

Hydrostatic

3.

Contact your Ariens Dealer.

 

 

transmission

 

 

 

 

and/or linkage

 

 

 

 

needs adjustment.

 

 

 

 

 

 

 

Unit creeps with

1.

Hydrostatic

1.

Contact your Ariens Dealer.

steering levers

 

transmission

 

 

in neutral

 

and/or linkage

 

 

position.

 

needs adjustment.

 

 

 

 

 

 

 

 

 

 

 

GB - 29

Image 29
Contents Zoom XL Introduction Table of ContentsProduct Registration Unauthorized Replacement PartsDelivery DisclaimerSafety Alerts SafetySafety Decals Locations NotationsKeep people away from unit while operating Serious Injury or Death Hot SurfacesEmission Control System Safety RulesPage Page Assembly Check Safety Interlock System Adjust SeatCheck Engine Oil Level Level Mower DeckControls and Features Operation Controls and FeaturesMower Lift Pedal Steering LeversFilling Fuel Tank Adjusting SeatGasoline Stopping in AN EmergencyStarting and Shutting OFF Engine Moving Unit ManuallyOperating Mower Transporting UnitInterval Task Action Maintenance ScheduleHours or Every Season Service and AdjustmentsTipping Seat Forward Leveling and Adjusting Pitch of Mower Deck Opening Deck Access PlateOpening and Closing Hood Replacing Mower BladePitch Of The Mower Blades From Side-To-Side Forward Pitch Of The Mower BladesForward Pitch of Mower Blades Side-To-Side PitchBattery Removal and Installation Remove Servicing BatteryJump-Starting Cleaning Battery and Battery CablesCharging the Battery Adjusting Steering Levers Replacing PTO Belt Check Hydraulic Fluid Level Replacing Hydrostatic BeltTo Add Hydraulic Fluid Change Hydraulic Fluid and FilterPurging the Hydraulic System Short Term Storage StorageLong Term Storage Fuel SystemTroubleshooting Blades do not PTO or mowerOff EngineAccessories Service PartsPoor cutting QualitySpecifications Consumer Mowing Equipment Limited Warranty Limitation of Remedy and Damages Your Warranty Rights and Obligations Disclaimer Evaporative Emission Warranty Parts ListAriens West Ryan Street Brillion, WI 54110-1072