Alamo 4211 MSL manual Storage, Lift and Bucket Cylinder Reassembly

Page 97
(SL-27)
(SL-26)

MAINTENANCE

Lift and Bucket Cylinder Reassembly

Note: Be careful not to damage seals and o-rings on edges or holes in cylinder tube. Inspect and remove burrs and sharp edges if necessary before reassembly.

1.Place rod seal (3) into groove inside cylinder head.

Note: Lips of seal (3) must be face inward and seal must be firmly seated in groove.

2.Install wiper seal (2) with lip of seal facing out and flush with top of cylinder head (5). Install wear ring (4) inside other end of head (5).

3.Place o-ring (7) with back-up washer (6) in groove on outside of head. Back-up washer must be on rod side.

4.Remove sharp edges on outer edge of the threaded end of shaft (1). Lubricate wiper seal (2) and rod seal

(3) in head and carefully slide head onto shaft.

5.Place o-ring (10), piston seal (11) and piston wear ring (8) in grooves on outside of piston (9). Note: For easier installation, place piston seal (11) in 120°F water to warm seal.

6.Slide piston (9) onto threaded end of shaft and install lock nut (12). Tighten lock nut to 100 lbs.

7.Lubricate piston wear ring (8) and piston seal (11) on piston, o-ring (7) and backup washer (6) on head and inside of cylinder tube (13), then carefully slide piston and head into cylinder tube (13).

8.Insert wire retaining ring (14) into slot in cylinder tube (13). Apply pressure to wire ring to thread it into groove while turning cylinder head.

Note: If cylinder has a countersunk hole, hook end of retaining wire into hole and turn cylinder head 1-1/2 turns to secure wire. End of hook may need to be ground to fit in countersunk hole.

Storage

Never crawl under or allow children to play around or on a loader that is disconnected from the tractor. The loader could fall crushing a person resulting in serious injury or death. (SL-13)

Do not remove the attachment from the loader when the loader is disconnected from the tractor. The attachment stabilizes the loader. If the attachment is removed, the loader will fall and could result in serious injury.

Only disconnect and store the loader on firm flat ground. Make sure the loader stands are properly installed and rest on firm ground or support blocks. If the stands sink or fail, the loader could fall causing serious injury.

NOTE: When loader hydraulics are disconnected from tractor, the tractor hydraulic circuit must be completed. Failure to do so will result in tractor hydraulic pump damage.

4211-4211SS MSL 01/11

Maintenance Section 5-7

© 2011 Alamo Group Inc.

MAINTENANCE

Page 96 Page 98
Image 97
Page 96 Page 98
Contents 4211 MSL To the Owner/Operator/Dealer Table of Contents Maintenance Section Safety Section General Safety Instructions and Practices Safety4211-4211SS MSL 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 Safety Safety 4211-4211SS MSL 01/11 Safety Section SL-33 Safety Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesDecal Location QTY Level Description Decal Description Loader Positions 4211-4211SS MSL 01/11 Safety Section Loader Safety Safety Federal Laws and Regulations Page Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Instructions AssemblyAssembly Proper Rear Ballasting and Wheel Spacing Dismounting Loader Dismounting Loader and Mounting Loader to TractorMounting Loader Attaching Pin on BucketMounting Attachment to Loader Mounting and Dismounting AttachmentAssembling Quick Attach Device Installing Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Page Operation Section Operation Standard Equipment and Specifications Operator Requirements Operation Personal Protective Equipment PPE Rops and Seat Belt Tractor RequirementsTractor Lighting and SMV Emblem Tractor Ballast Getting On and Off the TractorDismounting the Tractor Boarding the TractorStarting the Tractor Tractor Pre-Operation Inspection/Service Pre-Operation Inspection and ServiceLoader Pre-Operation Inspection and Service Mount Assembly OPS-L-0007B Do not Operate an Unsafe Tractor or Front END Loader Front END Loader PRE-OPERATION Inspection Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Filling the Bucket Operating the LoaderOperation Lifting the Load Carrying the Load Lowering the Bucket Dumping the BucketOperating with Float Control Loading from a Bank Operation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Transporting the Tractor and Implement Loader StorageShutting Down the Implement Operation Transporting on Public Roadways Operation Hauling the Tractor and Implement Troubleshooting Guide Page Maintenance Section Maintenance 4211-4211SS MSL 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Lift and Bucket Cylinder Disassembly Cylinder ServiceStorage Lift and Bucket Cylinder ReassemblyStore loader with attachment securely attached Proper Torque for Fasteners Maintenance Maintenance Rhino To the OWNER/OPERATOR/DEALER MSL 4211SS MSL Loader

4211 MSL specifications

The Alamo 4211 MSL stands out in the realm of compact RVs, blending functionality with innovative design to ensure an enjoyable travel experience. This model is specifically engineered to cater to the needs of outdoor enthusiasts, offering a harmonious balance of comfort and versatility.

One of the main features of the Alamo 4211 MSL is its spacious and thoughtfully designed interior. With a layout that optimizes the available space, it offers sleeping accommodations for up to four people, making it perfect for small families or groups of friends. The well-appointed kitchen includes modern appliances, such as a two-burner stove, a microwave, and a refrigerator, enabling travelers to prepare home-cooked meals on the road. Additionally, ample storage compartments throughout the unit provide practical solutions for organizing gear and personal items.

In terms of technology, the Alamo 4211 MSL incorporates advanced features that enhance the travel experience. An integrated entertainment system with Bluetooth capabilities allows occupants to enjoy their favorite music or movies, while LED lighting ensures energy efficiency and brightens the space. The model also comes with a comprehensive control panel, giving users the ability to monitor and manage various systems with ease, including water levels and battery status.

One of the standout characteristics of the Alamo 4211 MSL is its robust construction and user-friendly design. The exterior is built with durable materials, ensuring that it can withstand the rigors of outdoor adventures. The inclusion of high-quality insulation keeps the interior comfortable in various weather conditions, whether it be hot summers or cold winters.

The innovative pop-up roof feature is another notable aspect, allowing for increased headroom and a more spacious feel within the living area. This versatility makes it easier to enjoy activities inside the RV, whether it’s playing games or relaxing after a day of exploration.

Furthermore, the Alamo 4211 MSL's lightweight design contributes to better fuel efficiency and ease of towing. Its compact size enables access to more remote and scenic locations while still providing the comforts of home.

In conclusion, the Alamo 4211 MSL is a thoughtfully designed RV that caters to the needs of travelers seeking adventure without compromising on comfort. With its ideal combination of space, technology, and construction quality, it promises a rewarding experience for both seasoned RVers and newcomers alike.
Top Page Image Contents