Cal Spas LTR20111002 manual Electronic Control Operation, Your Spa

Page 24

24

Your Spa

9800 Electronic Control Operation

Initial Start-up

When first powered up, your spa will perform a self-diagnostic check and then automatically go into priming mode. The topside will display PR to indicate this. Priming mode will be active for less than five minutes. When the spa has finished priming, the heater will be activated and the water temperature will be maintained in stan- dard mode. The spa will automatically heat to 100°F (37.5°C) at start-up until you change the set temperature as listed in the “Temperature Adjustment” section below.

Operating

These instructions will describe features and options that your particular spa may not be equipped with.

Temperature Adjustment

80°F - 104°F (26..0°C - 40..0°C)

The start-up temperature is set at 100°F (37.5°C). The last measured temperature is constantly displayed on the control panel. Note that the last measured spa temperature is displayed. The displayed temperature will be updated

when the pump has been running for at least two minutes.

Press the “UP” or “DOWN” buttons once to display the set temperature. Each time either button is pressed again, the set temperature will increase or decrease depending on which button is pressed. After three seconds, the control panel will automatically display the last measured spa temperature.

Time

When time hasn’t been programmed, the “TIME” icon flashes. To set the time, press the “TIME” button and then the “MODE/PROG” button. Use the “UP” and “DOWN” buttons to adjust time. See the next page for more detailed instructions.

Standard, Economy, Sleep, and Standby Modes

Mode/Prog: This button is used to switch between standard, economy, and sleep modes.

1.Press “MODE/PROG” to enter mode program- ming.

2.Press the “DOWN” button to cycle through to the desired mode.

3.Press “MODE/PROG” to confirm selection.

Standard Mode: This is programmed to maintain the desired temperature. Note that the last measured spa temperature displayed is current only when the pump has been running for at least two minutes. The “STAND” icon will display until the mode is changed.

Economy Mode: Economy mode heats the spa to the set temperature only during filter cycles. The “ECON”

icon will display until the mode is changed. Pressing the “JETS 1” button while in economy mode puts the spa in standard-in-economy mode, which operates the same as standard mode but reverts back to economy mode automatically after one hour. During this time, pressing the “MODE/PROG” button will revert to econ- omy mode immediately.

Sleep Mode: Sleep mode heats the spa to within 20°F (6.7°C) of the set temperature only during filter cycles. The “SLEEP” icon will display until the mode is changed.

Standby Mode: Pressing “Warm” or “Cool” then “JETS 2” will turn off all spa functions temporarily. This is helpful when changing a filter. Pressing any button resets the spa.

Jets 1 and Jets 2

Press the “JETS 1” button once to turn pump 1 on or off and to shift between low and high speeds if equipped. If left running, the low speed turns off af- ter two hours and the high speed turns off after 15 minutes. On non-circulation systems, the low speed of pump 1 runs when the blower or any other pump is on. It may also activate for at least two minutes every 30 minutes to detect the spa temperature and then to heat to the set temperature if needed, depending upon the mode. When the low speed turns on au- tomatically, it cannot be deactivated from the panel; however, the high speed may be started.

Option

This is an optional feature. Press the “OPTION” but- ton to turn the optional equipment on and off. If left

Inground Spas

www.calspas.com

LTR20111002, Rev. A

Page 23 Page 25
Image 24
Page 23 Page 25
Contents LTR20111002, Rev. a 1/24/11 Cleaning and Maintenance Preparing for Your New Inground Spa Clear Water PlanElectronic Control Operation Appendix Important Safety Instructions Read This FirstHyperthermia Danger Inground Spa Installation Checklist Preparing for Your New Inground SpaInground Spa ForYour NewPlanning the Best Place for the Outdoor Equipment Pack Preparing forYour NewInground Spa Site Preparation SpaSpa Shell Dimensions and Side Views Preparing forYour New Inground SpaIG-401 Your New Inground Spa IG-402IG-403 IG-404 IG-405 IG-406 IG-407 Gfci and Wiring Requirements Testing the Gfci BreakerSpa Model Gfci Required Wires Required Electrical Requirements US and CanadaGfci Wiring Diagram Electrical Installation -- Europe RCD and Wiring RequirementsTesting the RCD Breaker RCD Wiring Diagram NewYour SpaIngroundForPreparing Installing the Inground Shell Equipment Pack Plumbing Connections Plumbing ConnectionsConnecting Plumbing to Remote Equipment Gate/Slice ValvesElectrical and Electronic Connection Preparing forYour New IngroundRemote Equipment Topside Control Panel Inground Spa Light Installation In- structions See figure belowPreparing forYour New Inground Spa Pouring the Deck Electronic Control Operation Your SpaSetting the Temperature Lock Preset Filter CyclesClean-up Cycle LightOperating SpaYour Diagnostic Messages Message Meaning Action Required No messageOn display DryMessage Meaning Action Required Snb SnsStby Adjustable Jets Diverter KnobsContents of this section Clear Water PlanClear PlanWater Key to Clear WaterTesting and Adjusting Spa Water Clear Water PlanBalancing the Total Alkalinity Balancing the pHUsing Chlorine as a Sanitizer Using Bromine as a SanitizerSanitation Chemical Safety Shocking the WaterFilter Cleaning Bather LoadStarting the Spa with Fresh Water Water PlanMaintenance Schedule Troubleshooting Water Clarity Problems Problem Probable Causes Possible SolutionsCleaning and Maintenance Removing and Reseating the PillowsSpa Cover Cleaning and Replacing the Filter Draining Your SpaWinterizing Cold Climate Draining Cleaning the Cover, Shell and Pillows CleaningFast Sheen Spa finish protecting wax Replacement Parts WarrantyAppendix Cal Spas Chemicals LTR20111002, Rev. a 1/24/11
Top Page Image Contents