Cal Spas Inground Spas manual Inground Spa Light Installation In- structions, See figure below

Page 14

14

Preparing forYour New Inground Spa

7.Once topside panel operation is verified. Turn off power, disconnect the extension loom from the circuit board and GENTLY route through conduit to complete installation.

NOTE: This loom and its connector are not meant to withstand heavy pulling. Make sure, when routing the extension loom and temperature sensor lines through conduit, you exercise extreme caution.

Once properly run through the conduit, repeat steps 5 and 6 above.

Inground Spa Light Installation In- structions

On spas ordered with inground lights, the factory installs the light niche for you. The next steps of installation should be performed by a qualified licensed electrician.

Always read and follow light manufacturer’s safety and installation instructions prior to installation and operation. Incorrect installation may damage the light and void its warranty.

The light circuit must be on a GFCI protected service (alone or with a switch).

The water resistant junction box (or for 12 volt models, the low voltage transformer) must be located:

•at least 8” (20 cm) above water level

•at least 4” (10 cm) above ground level, and

•at least 48” (121 cm) away from the spa..

See figure below.

Light niche and any metallic items in a 5’ (152 cm) radius must be properly bonded with #8 AWG grounding wire.

1.Connect rigid conduit to the 3/4” hub located at the back of the light niche and run to a water re- sistant junction box (or for 12 volt models to a low voltage transformer) no further than 25’ (7.6m).

Remember this is a water cooled light, so the con- duit and all connections must be leakproof.

2.Feed the light cord through the rigid conduit to the junction box, leaving at least 4 feet of cord at the end of the light fixture. This slack in the light cord will allow servicing without draining the spa in the future.

3.Wrap light cord slack around back of light housing and attach light to niche with mounting screw.

4.Cut the cord at the junction box, leaving at least

6” (15 cm) of cord to make connections.

5.Strip 6” (15 cm) of the out cord jacket to expose the three insulated wires. Be careful not to dam- age the insulation on the three inner wires.

6.Connect the three wires to the corresponding cir- cuit wires in the junction box and secure the junc- tion box cover in place.

7.Replace the light assembly in the niche and tight- en the special pilot screw.

8.Fill the spa until the underwater light is completely submerged in water before operating the light for more than 10 seconds. Turn on the main switch or circuit breaker, as well as the spa light control, to check for proper operation

Important: Make sure spa light is submerged in at least 18” of water prior to testing..

2009 Inground Spas

www.calspas.com

LTR20091002, Rev. B

Page 13 Page 15
Image 14
Page 13 Page 15
Contents LTR20091002, Rev. B 1/30/09 Electronic Control Operation Cleaning and MaintenancePreparing for Your New Inground Spa Clear Water Plan AppendixHyperthermia Danger Important Safety InstructionsRead This First Inground Spa Inground Spa Installation ChecklistPreparing for Your New Inground Spa ForYour NewInground Spa Site Preparation Planning the Best Place for the Outdoor Equipment PackPreparing forYour New SpaElectrical Requirements US and Canada Gfci and Wiring RequirementsTesting the Gfci Breaker ForYour New IngroundGfci Wiring Diagram Your New Inground SpaTesting the RCD Breaker Electrical Installation -- EuropeRCD and Wiring Requirements Preparing forYour New IngroundRCD Wiring Diagram Installing the Inground Shell Preparing forYour New Inground SpaPlumbing Connections Designer Spa SpecificationsEquipment Pack Plumbing Connections Identifying Plumbing LinesGate/Slice Valves Air TestWater Test Remote Equipment Topside Control Panel Connecting Plumbing to Remote EquipmentElectrical and Electronic Con- nection Inground Spa Light Installation In- structions See figure belowYour New Inground Spa Pouring the Deck Electronic Control Operation Your SpaOperating SpaYour RSA Periodic Reminder MessagesMessage Frequency Action Required RPH RCLOn display Diagnostic MessagesMessage Meaning Action Required No message DryStby Message Meaning Action RequiredSnb Sns Waterfalls Adjustable JetsDiverter Knobs Air VenturisKey to Clear Water Contents of this sectionClear Water Plan Clear Water PlanBalancing the Total Alkalinity Testing and Adjusting Spa WaterClear PlanWater Balancing the pHSanitation Using Chlorine as a SanitizerUsing Bromine as a Sanitizer Adding Sanitizer Tablets to the Chemical ChamberChemical Safety Shocking the WaterFilter Cleaning Bather LoadClear Water PlanStarting the Spa with Fresh Water Maintenance Schedule Day One Monday Del Zone Eclipse OzonatorStart Up Day Two FridayTroubleshooting Water Clarity Problems Problem Probable Causes Possible SolutionsSpa Cover Cleaning and MaintenanceRemoving and Reseating the Pillows Winterizing Cold Climate Draining Cleaning and Replacing the FilterDraining Your Spa Cleaning the Cover, Shell and Pillows CleaningFast Sheen Spa finish protecting wax Replacement Parts AppendixKeeping Fit with your Cal Spa Fitness Series Exercise ProgramConnecting the Exercise Equipment Cal Spas Chemicals LTR20091002, Rev. B 1/30/09

Inground Spas specifications

Cal Spas Inground Spas represent the pinnacle of luxury outdoor relaxation, seamlessly blending aesthetic appeal with cutting-edge technology. These spas are designed for avid spa enthusiasts who appreciate the benefits of hydrotherapy and socializing in an inviting environment. Crafted with premium materials, Cal Spas ensures durability and longevity, making them an investment that enhances any outdoor living space.

One of the standout features of Cal Spas Inground Spas is their customizable design. Clients can choose from a variety of dimensions, shapes, and layouts to fit their particular yard space and personal tastes. Whether opting for a sleek contemporary style or a classic design, each spa can be tailored to create a harmonious outdoor oasis. The versatility of these spas allows for various configurations, integrating seamlessly with landscaping, patios, or even decking.

In terms of technology, Cal Spas incorporates state-of-the-art hydrotherapy systems that provide personalized wellness benefits. The spa jets are strategically placed to target specific muscle groups, ensuring an invigorating and relaxing experience. With options for adjustable jets, users can customize the intensity of their massage, further enhancing the therapeutic effects. Additionally, many models come equipped with energy-efficient heating systems, allowing users to enjoy a warm soak without significant hikes in utility bills.

The integration of smart technology sets Cal Spas apart from its competitors. With optional Wi-Fi connectivity, users can control their spa remotely through a mobile app. This feature enables easy temperature adjustments, scheduling filtration cycles, and even turning the lights on or off, all at the user's fingertips. The LED lighting options not only aid in creating a serene ambiance but also enhance safety during nighttime use.

Moreover, Cal Spas ensures user comfort and safety with ergonomic seating designed to accommodate various body types while optimizing relaxation. The non-slip surfaces and advanced water purification systems further enhance user experience, prioritizing health and security.

In summary, Cal Spas Inground Spas are meticulously designed to provide an unparalleled outdoor spa experience. With their customizable designs, advanced hydrotherapy features, smart technology integration, and a commitment to user comfort, these spas are perfect for anyone looking to create a luxurious retreat in their own backyard. Whether seeking a place to unwind after a long day or entertain friends and family, Cal Spas delivers an exceptional spa experience that stands the test of time.
Top Page Image Contents