Cal Spas LTR20111058 manual Filling and Powering Up Your Portable Spa, Preparing forYour New

Page 10

8

Portable Spa

Filling and Powering Up Your Portable Spa

Never fill your spa with soft water.

Soft water makes it impossible to maintain the proper water chemistry and may cause the wa- ter to foam, which will ultimately harm the finish of the spa and void your warranty.

Preparing forYour New

1.Once the spa has been placed on an approved surface and has been correctly wired by a licensed electrician, inspect all plumbing connections in the equipment area of your spa. Ensure that these connections are secure and that they did not loos- en during shipment.

2.If equipped, open all gate valves in the equipment area. Before operating the spa, these valves must be in the up or “open” position.

VERY IMPORTANT!

Never run the spa with the gate valves closed or without water circulating for long periods of time. Be careful not to over-tighten the plumbing fittings.

3.Remove the cartridge from filter canister.

4.Place a garden hose in the filter canister and fill your spa with regular tap water about six inches from the top.

VERY IMPORTANT!

Always fill the spa through the filter canister! Failure to do so may cause air to be trapped in the filtration sys- tem and prevent the pumps from op- erating properly.

5.Presoak the filters in spa water.

VERY IMPORTANT!

You must presoak the filters before inserting them in the filter canister. Dry filters can allow air into the fil- tration system which can cause pump failure.

6.Once the water is at the correct level and air is bled, plug in the spa into a dedicated electrical outlet.

Note: When the power is turned on to the spa, the controls will perform a diagnostic check for approximately five minutes. When the diagnostic is complete, the spa will automatically operate at filter speed and continue heating until the spa wa- ter temperature reaches the default temperature of 100˚F.

8.If no water is flowing when the pump is running, there could be an air pocket at the suction side of the pump. Shut off power to the spa and loosen the pump union on the suction side of the pump to bleed the air. When air is bled, turn power back on.

9.Install the pre-soaked filters into the filter canis- ter.

The spa is now ready for use.

2011 Genesis Portable Spa

www.calspas.com

LTR20111058, Rev. B

Page 9 Page 11
Image 10
Page 9 Page 11
Contents LTR20111058, Rev. B 4/27/11 Operating Your Spa Cleaning and MaintenancePreparing for Your New Portable Spa Clear Water PlanImportant Safety Instructions This FirstRead First!This ForYour New Portable Spa Preparing for Your New Portable SpaPlanning the Best Location Preparing a Good FoundationPreparing forYour New Portable Spa Electrical InstallationTesting the Gfci 110V / 60 HzYour New Portable Spa RCD and Wiring RequirementsTesting the RCD Breaker 230V / 50 HzNewYour SpaPortable RCD Wiring DiagramForPreparing Circuit Board Connection Portable Spa Filling and Powering Up Your Portable SpaPreparing forYour New Electronic Control Operation Operating Your SpaSpa Operating SpaYour Setting Filtration CyclesAutomatic Time outs On display Diagnostic MessagesMessage Meaning Action Required No message DrYSnb Message Meaning Action RequiredSnA SnSJets LED Light OperationClear PlanWater Contents of this sectionClear Water Plan Key to Clear WaterBalancing the Total Alkalinity Testing and Adjusting Spa WaterClear Water Plan Balancing the pHUsing Bromine as a Sanitizer Using Chlorine as a SanitizerSanitation Chemical Safety Shocking the WaterCleaning the Filter Basket Cleaning the FilterBather Load Starting the Spa with Fresh Water Water PlanMaintenance Schedule Troubleshooting Water Clarity Problems Problem Probable Causes Possible SolutionsDo not run the spa with the access panel removed Cleaning and MaintenanceRemoving the Access Panel Draining Your Portable SpaWinterizing Cold Climate Draining Cleaning and MaintenanceInstalling Cover Latches Freeze damage is not covered by your war- rantyVinyl and Leather Cleaner Cleaning and Replacing the FilterCleaning the Cover Periodic MaintenancePrior to Spa Start-Up and Refilling Cleaning the ShellAll-Purpose Cleaner Spa Finish Cleaning Fast Sheen Spa Finish Protecting WaxReplacement Parts AppendixLimited Warranty Customer Service Proration of WarrantyActs That Will Void This Warranty DisclaimersCal Spas Chemicals LMS Customer Service Department Locating the product serial number

LTR20111058 specifications

Cal Spas LTR20111058 is a state-of-the-art hot tub designed to offer a perfect blend of luxury and relaxation. It showcases a variety of features and technologies that cater to both functionality and comfort, making it an ideal choice for those seeking to enhance their outdoor living space.

One of the standout characteristics of the LTR20111058 is its spacious interior, accommodating up to six people. This generous seating capacity makes it perfect for family gatherings or social get-togethers with friends. The arrangement of the seats is designed to provide maximum comfort and promote soothing conversations, featuring ergonomic contours that allow users to unwind in blissful relaxation.

The LTR20111058 is equipped with multiple hydrotherapy jets, which can be strategically adjusted to target specific muscle groups. These jets provide a therapeutic massage experience that can alleviate stress and tension, making it an all-around wellness solution. The variable jet pressure settings enable users to customize their soaking experience, ensuring that everyone finds the perfect level of relaxation.

In addition to its physical features, the hot tub incorporates advanced technology, including a user-friendly control panel that allows for easy adjustments to temperature, lighting, and jet functions. The digital controls provide a level of convenience, ensuring users can effortlessly create their desired atmosphere. Furthermore, the energy-efficient heating system is designed to maintain optimal water temperatures while minimizing operational costs, making the LTR20111058 an environmentally friendly option.

Durability is another key aspect of the Cal Spas LTR20111058. Constructed with high-quality materials, the cabinet and shell are built to withstand varying weather conditions while maintaining their aesthetic appeal. The hot tub is insulated effectively, allowing it to retain heat, thereby enhancing energy efficiency and ensuring a consistently enjoyable experience.

Safety features are also paramount, with slip-resistant surfaces and secure handrails incorporated into the design. Additionally, the LTR20111058 is built with advanced water purification systems, ensuring that the water remains clean and safe for users at all times.

Overall, the Cal Spas LTR20111058 combines luxury, comfort, and innovative technology, making it a compelling choice for anyone looking to add a touch of serenity to their home. Its thoughtful design and advanced features promise not only relaxation but also a revitalizing escape from the everyday hustle and bustle.
Top Page Image Contents