Exmark 4500-450 manual Stopping the Machine, Adjusting the Height of Cut, Forward, Backward

Page 22

Operation

CAUTION

Machine can spin very rapidly by positioning one lever too much ahead of the other. Operator may lose control of the machine, which may cause damage to the machine or injury.

Use caution when making turns.

Slow the machine down before making sharp turns.

Forward

1.Move the levers to the center, unlocked position.

2.To go forward, slowly push the motion control levers forward (Figure 9).

Backward

1.Move the levers to the center, unlocked position.

2.To go backward, slowly pull the motion control levers rearward (Figure 9).

To go straight, apply equal pressure to both motion control levers (Figure 9).

To turn, release the pressure on the motion control lever toward the direction you want to turn (Figure 9).

To stop, push the motion control levers to neutral.

Stopping the Machine

To stop the machine, move the motion control levers to neutral and outward to the neutral position, disengage the blade control switch, move the throttle lever to between Fast and half throttle, and turn the ignition key to off. Remember to remove the key from the ignition switch.

 

Figure 9

 

1.

Neutral position

3.

Backward

2.

Center unlock position

4.

Forward

To go straight, apply equal pressure to both motion control levers (Figure 9).

To turn, pull back on the motion control lever toward the direction you want to turn (Figure 9).

The farther you move the motion control levers in either direction, the faster the machine will move in that direction.

To stop, pull the motion control levers to neutral.

CAUTION

Children or bystanders may be injured if they move or attempt to operate the mower while it is unattended.

Always remove the ignition key and move the motion control levers outward to the neutral position and apply the parking brake when leaving the machine unattended, even if just for a few minutes.

Adjusting the Height of Cut

1.Raise the deck to the transport position (4.5 inch (114 mm) cut height) by pushing the foot actuated lever forward (Figure 10). The transport lever will automatically engage and will drop into place.

22

Image 22
Contents Quest California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol General OperationChildren ServiceSlope Operation TowingExmark Riding Mower Safety General ServiceSafety and Instructional Decals 93-7009109-6035 116-0532 PTO Symbols 109-8965 Model Numbers SpecificationsSystems Dimensions Product Overview Torque RequirementsOperation ControlsParking Brake Lever Think Safety FirstOperating Instructions Height-of-Cut Foot LeverRecommended Gasoline Starting the Engine Using Stabilizer/Conditioner Checking the Engine Oil Level Gasoline/Alcohol blendsEngaging the Blades Operating the BladesStopping the Engine Disengaging the BladesTesting the Safety Interlock System Safety Interlock SystemUnderstanding the Safety Interlock System Driving Forward or BackwardForward Adjusting the Height of CutStopping the Machine BackwardGround. Do Not adjust rollers to support the deck Adjusting the Anti-Scalp RollersPositioning the Seat Changing the Seat Ride Suspension Adjusting the Motion Control LeversPushing the Machine by Hand To Operate the Machine Side DischargeTransporting Transporting a UnitOperating Tips Blade Maintenance When StoppingKeep the Underside of the Mower Clean Cutting SpeedMaintenance Recommended Maintenance SchedulesLubrication Accessing the BatteryRaising the Seat Greasing the BearingsServicing the Air Cleaner Engine MaintenanceServicing Paper Element Changing the Oil and Filter Servicing the Engine OilChecking the Oil Level Remove the foam sleeve from the elementChecking the Hydraulic Oil Level Change the Hydraulic System Filter Servicing the Spark PlugRemoving the Spark Plug Cleaning the Blower HousingInstalling the Spark Plug Checking the Spark PlugReplacing the Fuel Filter Fuel System MaintenanceElectrical System Maintenance Fuel filter is in the fuel line between the tank and engineRemoving the Battery Charging the BatteryCharging the Battery Installing the Battery Servicing the Fuses and RelayBefore Inspecting or Servicing the Blades Drive System Maintenance Checking the Tire PressureMower Maintenance Servicing the Cutting Blades Inspecting the BladesRemoving the Blades Checking for Loose Blades or Damaged Spring Disc WashersSharpening the Blades Mower Belt MaintenanceInstalling the Blades Inspecting the BeltsLeveling the Mower Deck Off the clutch pulley as shown in and FigureAdjusting the Blade Slope Front-to-Rear Blade SlopeDeck lift arm Deck hanger Float retaining nut Replacing the Discharge Deflector Locate items shown in FigureTracking Adjustment Washing the Underside of the MowerMaintenance Cleaning and Storage StorageTroubleshooting Problem Possible Cause Corrective ActionTo Pushing the Machine by Hand Schematics DiagramElectrical Logic Schematic Exmark Quest Turf Equipment Service Record Page Page See EXMARK’S Complete Line of Accessories and Options