Exmark 4500-450 manual Charging the Battery, Removing the Battery

Page 36

Maintenance

Charging the Battery

Removing the Battery

WARNING

Battery terminals or metal tools could short against metal machine components causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.

•When removing or installing the battery, Do Not allow the battery terminals to touch any metal parts of the machine.

•Do Not allow metal tools to short between the battery terminals and metal parts of the machine.

1.Park the machine on a level surface and disengage the blade control switch.

2.Move the motion control levers outward to the neutral position, engage parking brake stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position.

3.Raise the seat.

4.Disconnect the negative (black) ground cable from the battery post (Figure 28). Retain all fasteners.

Figure 28

1.

Negative battery post

4.

Positive battery post

2.

Bolt, washer, and nut

5.

Battery strap

3.

Terminal boot

6.

Battery

 

 

 

 

WARNING

Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.

•Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable.

•Always connect the positive (red) battery cable before connecting the negative (black) cable.

5.Slide the rubber cover up the positive (red) cable. Disconnect the positive (red) cable from the battery post. Retain all fasteners.

6.Remove the battery strap (Figure 28) and lift the battery from the battery tray.

Charging the Battery

1.Remove the battery from the chassis; refer to Removing the Battery.

2.Allowing batteries to stand for an extended period without recharging them will result in reduced performance and service life. To preserve optimum battery performance and life, recharge batteries in storage when the open circuit voltage drops to 12.4 volts.

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

3.Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table below and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

Important: Make sure the negative battery cables are disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart below for recommended charger settings).

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Quest California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices General OperationService Slope OperationChildren TowingExmark Riding Mower Safety General ServiceSafety and Instructional Decals 93-7009109-6035 116-0532 PTO Symbols 109-8965 Specifications Model NumbersSystems Dimensions Product Overview Torque RequirementsOperation ControlsThink Safety First Operating InstructionsParking Brake Lever Height-of-Cut Foot LeverRecommended Gasoline Using Stabilizer/Conditioner Checking the Engine Oil LevelStarting the Engine Gasoline/Alcohol blendsOperating the Blades Stopping the EngineEngaging the Blades Disengaging the BladesSafety Interlock System Understanding the Safety Interlock SystemTesting the Safety Interlock System Driving Forward or BackwardAdjusting the Height of Cut Stopping the MachineForward BackwardAdjusting the Anti-Scalp Rollers Ground. Do Not adjust rollers to support the deckPositioning the Seat Adjusting the Motion Control Levers Changing the Seat Ride SuspensionPushing the Machine by Hand Side Discharge TransportingTo Operate the Machine Transporting a UnitOperating Tips When Stopping Keep the Underside of the Mower CleanBlade Maintenance Cutting SpeedMaintenance Recommended Maintenance SchedulesAccessing the Battery Raising the SeatLubrication Greasing the BearingsEngine Maintenance Servicing the Air CleanerServicing Paper Element Servicing the Engine Oil Checking the Oil LevelChanging the Oil and Filter Remove the foam sleeve from the elementChecking the Hydraulic Oil Level Change the Hydraulic System Filter Servicing the Spark PlugCleaning the Blower Housing Installing the Spark PlugRemoving the Spark Plug Checking the Spark PlugFuel System Maintenance Electrical System MaintenanceReplacing the Fuel Filter Fuel filter is in the fuel line between the tank and engineCharging the Battery Removing the BatteryCharging the Battery Installing the Battery Servicing the Fuses and RelayDrive System Maintenance Checking the Tire Pressure Mower Maintenance Servicing the Cutting BladesBefore Inspecting or Servicing the Blades Inspecting the BladesRemoving the Blades Checking for Loose Blades or Damaged Spring Disc WashersMower Belt Maintenance Installing the BladesSharpening the Blades Inspecting the BeltsLeveling the Mower Deck Off the clutch pulley as shown in and FigureAdjusting the Blade Slope Front-to-Rear Blade SlopeDeck lift arm Deck hanger Float retaining nut Replacing the Discharge Deflector Locate items shown in FigureTracking Adjustment Washing the Underside of the MowerMaintenance Cleaning and Storage StorageTroubleshooting Problem Possible Cause Corrective ActionTo Pushing the Machine by Hand Schematics DiagramElectrical Logic Schematic Exmark Quest Turf Equipment Service Record Page Page See EXMARK’S Complete Line of Accessories and Options

4500-450 specifications

The Exmark 4500-450 is a top-tier commercial-grade zero-turn mower that has gained immense popularity among landscaping professionals for its advanced features, superior performance, and durability. Designed to tackle the toughest mowing tasks, the 4500-450 stands out for its reliability and innovative technologies.

One of the defining characteristics of the Exmark 4500-450 is its powerful engine. Equipped with a robust Kohler or Kawasaki engine, this model delivers impressive horsepower, ensuring that it can handle even the most demanding terrains with ease. This power allows for efficient cutting, enabling users to complete jobs more quickly without sacrificing quality.

The Exmark 4500-450 features a commercial-grade cutting deck that is fully adjustable to provide a clean and professional-looking cut. Its cutting width can range from 48 to 60 inches, making it versatile enough to handle various lawn sizes and types. The deck is designed with a unique airflow management system that optimizes grass lift, ensuring even and consistent results.

One of the standout technologies in the Exmark 4500-450 is its patented UltraCut deck design. This innovative feature promotes superior cutting performance while reducing clumping and providing a finer mulching capability. Additionally, the deck is designed for easy cleaning, which helps maintain the mower’s performance over time.

Comfort and usability are top priorities for the Exmark 4500-450. It boasts an ergonomic seat with high back support, reducing operator fatigue during long mowing sessions. The intuitive control system allows for smooth maneuverability, even in tight spaces, making it ideal for commercial landscaping work.

Moreover, the Exmark 4500-450 is built with durability in mind. Constructed from high-quality materials, it is designed to withstand the rigors of daily use. Its heavy-duty frame and components contribute to its long lifespan, ensuring that it remains a reliable workhorse for years to come.

In conclusion, the Exmark 4500-450 is an exceptional choice for professionals seeking a powerful, efficient, and durable zero-turn mower. With its high-performance engine, innovative cutting technologies, and user-friendly features, it sets a standard in commercial landscaping equipment, delivering results that exceed expectations while making the mowing process as efficient and comfortable as possible.
Top Page Image Contents