Check Engine Oil Level, Check Battery Charge

Maintenance

Periodic Maintenance

Check Engine Oil Level

Service Interval: Before each use or daily

1.Stop engine and wait for all moving parts to stop. Make sure unit is on a level surface.

2.Check with engine cold.

3.Clean area around dipstick. Remove dipstick and wipe oil off. Reinsert the dipstick and push it all the way down into the tube. Do Not screw into place. Remove the dipstick and read the oil level.

4.If the oil level is low, wipe off the area around the oil fill cap, remove cap and fill to the “FULL” mark on the dipstick. Use oil as specified in Engine Owner’s Manual. Do Not overfill.

Important: Do Not operate the engine with the oil level below the “LOW” (or “ADD”) mark on the dipstick, or over the “FULL” mark.

Check Battery Charge

Service Interval: Monthly

WARNING

CALIFORNIA

Proposition 65 Warning

Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

Allowing batteries to stand for an extended period of time without recharging them will result in reduced performance and service life. To preserve optimum battery performance and life, recharge batteries in storage when the open circuit voltage drops to 12.4 volts.

Note: To prevent damage due to freezing, battery should be fully charged before putting away for winter storage.

Check the voltage of the battery with a digital voltmeter. Locate the voltage reading of the battery in the table and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater.

Important: Make sure the negative battery cable is disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart for recommended charger settings).

Voltage	Percent	Maximum	Charging
Reading	Charge	Charger	Interval
		Settings
12.6 or	100%	16 volts/7	No
greater		amps	Charging
			Required
12.4 – 12.6	75–100%	16 volts/7	30 Minutes
		amps
12.2 – 12.4	50–75%	16 volts/7	1 Hour
		amps
12.0–12.2	25–50%	14.4 volts/4	2 Hours
		amps
11.7–12.0	0–25%	14.4 volts/4	3 Hours
		amps
11.7 or less	0%	14.4 volts/2	6 Hours or
		amps	More

Recommended Jump

Starting Procedure

Service Interval: As required

1.Check the weak battery for terminal corrosion (white, green, or blue “snow”), it must be cleaned off prior to jump starting. Clean and tighten connections as necessary.

CAUTION

Corrosion or loose connections can cause unwanted electrical voltage spikes at anytime during the jump starting procedure.

Do Not attempt to jump start with loose or corroded battery terminals or damage to the engine may occur.

DANGER

Jump starting a weak battery that is cracked, frozen, has low electrolyte level, or an open/shorted battery cell, can cause an explosion resulting in serious personal injury.

Do Not jump start a weak battery if these conditions exist.

4500-528 specifications

The Exmark 4500-528 is a formidable piece of equipment in the realm of professional landscaping and lawn maintenance. Renowned for its robust build and high-performance capabilities, this zero-turn mower is engineered for efficiency, agility, and maneuverability, making it an ideal choice for both commercial landscapers and passionate homeowners.

One of the standout features of the Exmark 4500-528 is its powerful engine. It is equipped with a reliable engine option that delivers impressive horsepower, allowing for faster mowing speeds and better handling of various terrains. The mowers are designed to tackle even the toughest grass conditions, making them suitable for large lawns and challenging landscapes.

The 4500-528 incorporates Exmark’s patented UltraCut deck design, which is specifically designed to optimize mowing efficiency. The deck's advanced cutting technology ensures a clean, even cut, promoting healthier grass growth while minimizing clumping and discharge issues. Furthermore, the mower is available in different cutting deck sizes, allowing users to choose based on their specific requirements and preferences.

Operator comfort is another hallmark of the Exmark 4500-528. The mower features a comfortable, adjustable seat, allowing users to maintain optimal posture during extended mowing sessions. With intuitive controls and a user-friendly interface, operators can easily manage the mower's numerous functions, including speed adjustments and deck height settings.

In terms of durability, the Exmark 4500-528 is built to last. Its heavy-duty frame and high-quality components ensure that it can withstand the rigors of professional use. The mower's tires are designed for traction and stability on various surfaces, enhancing its performance in different weather conditions.

Another impressive characteristic of the Exmark 4500-528 is its fuel efficiency. It is designed to maximize fuel economy while maintaining powerful performance, reducing operational costs for users. Additionally, the ease of maintenance associated with the mower ensures that it remains in top working condition with minimal effort.

Lastly, the Exmark 4500-528 is equipped with cutting-edge technologies, including improved steering control and enhanced safety features. These advancements not only make operations smoother but also enhance the safety of the operator and bystanders.

In summary, the Exmark 4500-528 is a premier zero-turn mower that combines power, precision, comfort, and durability, making it an essential asset for anyone serious about lawn care. Whether for commercial purposes or personal use, this mower delivers exceptional performance and extensive versatility.