Exmark 4500-528 manual Check Mower Blades

Page 24

Maintenance

2.Make sure the booster is a good and fully charged lead acid battery at 12.6 volts or greater. Use properly sized jumper cables (4 to 6 AWG) with short lengths to reduce voltage drop between systems. Make sure the cables are color coded or labeled for the correct polarity.

CAUTION

Connecting the jumper cables incorrectly (wrong polarity) can immediately damage the electrical system.

Be certain of battery terminal polarity and jumper cable polarity when hooking up batteries.

Note: The following instructions are adapted from the SAE J1494 Rev. Dec. 2001 – Battery Booster Cables – Surface Vehicle Recommended Practice (SAE – Society of Automotive Engineers).

WARNING

Batteries contain acid and produce explosive gases.

•Shield the eyes and face from the batteries at all times.

•Do Not lean over the batteries.

Note: Be sure the vent caps are tight and level. Place a damp cloth, if available, over any vent caps on both batteries. Be sure the vehicles do not touch and that both electrical systems are off and at the same rated system voltage. These instructions are for negative ground systems only.

3.Connect the positive (+) cable to the positive (+) terminal of the discharged battery that is wired to the starter or solenoid as shown in Figure 10.

Figure 10

1.Positive (+) cable on discharged battery

2.Positive (+) cable on booster battery

3.Negative (–) cable on the booster battery

4.Negative (–) cable on the engine block

5.Booster battery

6.Discharged battery

7.Engine block

4.Connect the other end of the positive cable to the positive terminal of the booster battery.

5.Connect the black negative (–) cable to the other terminal (negative) of the booster battery.

6.MAKE THE FINAL CONNECTION ON THE ENGINE BLOCK OF THE STALLED VEHICLE (NOT TO THE NEGATIVE POST) AWAY FROM THE BATTERY. STAND BACK.

7.Start the vehicle and remove the cables in the reverse order of connection (the engine block (black) connection is the first to disconnect).

Check Mower Blades

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lift deck and secure in raised position as stated in the Clean Grass Build-Up Under Deck procedure.

3.Inspect blades and sharpen or replace as required.

4.Reinstall blades (if they were removed) in the following order:

A.Install bushing through blade with bushing flange on bottom (grass) side of blade.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Turf Tracer California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 103-2242 103-2243 103-4935 103-2432 116-0404 117-2718 Specifications Model NumbersSystems Dimensions Product Overview Torque RequirementsOperation ControlsPre-Start Operating Instructions Driving the Machine Drive Lever/Neutral Lock Latch OperationDriving Forward Driving in ReverseAdjusting the Cutting Height Adjusting the Anti-Scalp RollersTransporting Transporting a UnitOperation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Recommended Jump Starting ProcedureDo Not jump start a weak battery if these conditions exist Check Engine Oil LevelCheck Mower Blades Check Safety Interlock System Service Air Cleaner Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Condition Of Belts Lubricate Grease FittingsLubricate Caster Wheel Hubs Remove Engine Shrouds and Clean Cooling Fins Check Spark PlugsChange Fuel Filter Change Hydraulic System Filter Hydraulic System Air PurgeLevel Fuel Tank Mounting Hardware Specifications Thread Locking AdhesivesPark Brake Adjustment Hydro Drive Linkage AdjustmentMobil HTS Grease Or Food-Grade Anti-seize Deck LevelingAdjust Neutral Control Linkages Adjust Hydro Control LinkagesTracking Adjustment Drive Lever Linkage AdjustmentHydro Pump Spring Tension Setting Electric Clutch AdjustmentClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Schematics Electrical DiagramElectrical Logic Schematic Hydraulic Diagram Exmark Commercial Turf Equipment Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

4500-528 specifications

The Exmark 4500-528 is a formidable piece of equipment in the realm of professional landscaping and lawn maintenance. Renowned for its robust build and high-performance capabilities, this zero-turn mower is engineered for efficiency, agility, and maneuverability, making it an ideal choice for both commercial landscapers and passionate homeowners.

One of the standout features of the Exmark 4500-528 is its powerful engine. It is equipped with a reliable engine option that delivers impressive horsepower, allowing for faster mowing speeds and better handling of various terrains. The mowers are designed to tackle even the toughest grass conditions, making them suitable for large lawns and challenging landscapes.

The 4500-528 incorporates Exmark’s patented UltraCut deck design, which is specifically designed to optimize mowing efficiency. The deck's advanced cutting technology ensures a clean, even cut, promoting healthier grass growth while minimizing clumping and discharge issues. Furthermore, the mower is available in different cutting deck sizes, allowing users to choose based on their specific requirements and preferences.

Operator comfort is another hallmark of the Exmark 4500-528. The mower features a comfortable, adjustable seat, allowing users to maintain optimal posture during extended mowing sessions. With intuitive controls and a user-friendly interface, operators can easily manage the mower's numerous functions, including speed adjustments and deck height settings.

In terms of durability, the Exmark 4500-528 is built to last. Its heavy-duty frame and high-quality components ensure that it can withstand the rigors of professional use. The mower's tires are designed for traction and stability on various surfaces, enhancing its performance in different weather conditions.

Another impressive characteristic of the Exmark 4500-528 is its fuel efficiency. It is designed to maximize fuel economy while maintaining powerful performance, reducing operational costs for users. Additionally, the ease of maintenance associated with the mower ensures that it remains in top working condition with minimal effort.

Lastly, the Exmark 4500-528 is equipped with cutting-edge technologies, including improved steering control and enhanced safety features. These advancements not only make operations smoother but also enhance the safety of the operator and bystanders.

In summary, the Exmark 4500-528 is a premier zero-turn mower that combines power, precision, comfort, and durability, making it an essential asset for anyone serious about lawn care. Whether for commercial purposes or personal use, this mower delivers exceptional performance and extensive versatility.
Top Page Image Contents