Exmark 4500-352 manual Introduction, Model No Serial No

Page 3
Introduction

Introduction

CONGRATULATIONS on the purchase of your Exmark Mower. This product has been carefully designed and manufactured to give you a maximum amount of dependability and years of trouble-free operation.

This manual contains operating, maintenance, adjustment, and safety instructions for your Exmark mower.

BEFORE OPERATING YOUR MOWER, CAREFULLY READ THIS MANUAL IN ITS ENTIRETY.

By following the operating, maintenance, and safety instructions, you will prolong the life of your mower, maintain its maximum efficiency, and promote safe operation.

If additional information is needed, or should you require trained mechanic service, contact your authorized Exmark equipment dealer or distributor.

All Exmark equipment dealers and distributors are kept informed of the latest methods of servicing and are equipped to provide prompt and efficient service in the field or at their service stations. They carry ample stock of service parts or can secure them promptly for you from the factory.

All Exmark parts are thoroughly tested and inspected before leaving the factory, however, attention is required on your part if you are to obtain the fullest measure of satisfaction and performance.

Whenever you need service, genuine Exmark parts, or additional information, contact an Authorized Service Dealer or Exmark Customer Service and have the model and serial numbers of your product ready.

Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided.

Figure 1

1. Model and serial number location

Model No.

Serial No.

3

Image 3
Contents For Serial Nos 790,000 & Higher METROCALIFORNIA Proposition 65 Warning Model No Serial No IntroductionContents ALERT! YOUR SAFETY IS INVOLVED SafetySafety Alert Symbol SafetyKeep away from eyes and skin Never siphon by mouth DANGERAvoid prolonged breathing of vapors Keep face away from nozzle and gas tank/container openingRemove accumulated debris from muffler and engine area OperationSlope Operation Allow engine parts, especially the muffler, to cool before touchingDo Not mow near drop-offs or near water Maintenance and StorageDo Not mow slopes when grass is wet Mow across slopes, never up and downSafety and Instructional Decals ECS Units Only Pistol Grip Units Only 48 inch Units OnlyModel Numbers SpecificationsSpecifications Safety Interlock SystemCutting Deck DimensionsCurb Weight Torque RequirementsOperation Product OverviewOperation ControlsChoke Control “Off-Run” SwitchDrive Levers Neutral Lock/Park Brake LatchesStarting the Engine Pre-StartOperating Instructions Open the Fuel Shut-Off ValveFor ECS Handles Driving the MachineDrive Lever/Neutral Lock/Park Brake Latch Operation For Pistol Grip HandlesTransporting a Unit If necessary, use assistance when loadingTransporting Changing GearsMaintenance Recommended Maintenance SchedulesMaintenance Check Engine Oil Level Periodic MaintenanceService Interval Before each use or daily Service Interval As requiredService Interval After the first 5 hours Check Safety Interlock SystemService Pre-Cleaner Element and Air Cleaner SERVICE DEALERCheck Condition Of Belts Service Interval Every 40 hoursNote See chart for service intervals Check Tire PressuresYearly-Replace gearbox grease Service Interval Every 160 hoursCheck Spark Plugs Change Fuel FilterMobil HTS Grease Or Food-Grade Anti-seize AdjustmentsAdjusting the Cutting Height Thread Locking AdhesivesHeight CuttingAxle Number Of SpacersAdjusting the Axle Position 3. Place the drive levers in the “park brake” position Adjusting the Number of Spacers below Caster Support HubAdjusting the Cutting Height with Blade Spacers Transmission Belt AdjustmentWheel Drive Belt Pulley Scrapers Engine to Mower Deck Belt48 inch Deck Shown for Reference Only Belt Guide Adjustment Blade Brake AdjustmentBrake and Wheel Drive Linkage Adjustment Right Side of Unit Shown Shifter Lever AdjustmentShifter Detent Adjustment PTO Safety Switch AdjustmentHandle Height Adjustment More traction applied as Wheel Drive Spring Tension AdjustmentUpper Handle Upper HoleRemove Engine Shrouds and Clean Cooling Fins CleaningClean Engine and Exhaust System Area Clean Debris From MachineTroubleshooting TroubleshootingCutting blades is/are bent or unbalanced Schematics SchematicsOwner’s Responsibilities Exmark Commercial Turf Equipment2 Year Limited Warranty Instructions for Obtaining Warranty ServicePage WALK-BEHIND ACCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF ACCESSORIES AND OPTIONSMID-MOUNT RIDING ACCESSORIES AND OPTIONS OUT-FRONT RIDING ACCESSORIES AND OPTIONS