Ferris Industries 5900629, 5901170, 5900625, 5900624, 5900619 Attaching a Trailer, Proper Mulching

Page 26

Operation

Operation

Proper Mulching

Mulching consists of a mower deck which cuts and recuts clippings into tiny particles and which then blows them down INTO the lawn. These tiny particles decompose rapidly into by-products your lawn can use. UNDER PROPER CONDITIONS, your mulching mower will virtually eliminate noticeable clippings on the lawn surface.

NOTE: When mulching under heavy cutting conditions, a rumbling sound may be present and is normal.

MULCHING REQUIRES EXCELLENT MOWING CONDITIONS

Mulching mowers cannot function properly if the grass is wet, or if the grass is simply to high to cut. Even more than normal mowing, mulching requires that the grass be dry and the the appropriate amount is cut.

Do not use the mower as a mulching mower during the first two or three mowings in the spring. The long grass blades, quick growth, and often wetter conditions are more suitable for broadcasting (side- discharging) or grass bagging operation.

ENGINE SPEED & GROUND SPEED FOR

BROADCASTING

Use full engine throttle matched with a slow ground speed so that clippings will be finely cut. Ground speed while mulching should be HALF of the speed that would be used when broadcasting (side discharging) under similar conditions. Since mulching requires more horsepower than broadcasting, using a slower ground speed is vitally important for proper mulching operation.

HOW MUCH GRASS TO MULCH

The best mulching action typically results from cutting only the top 1/2 inch to 3/4 inch of grass blade. This provides short clippings which decompose properly (much more quickly than longer clippings). The ideal cutting height will vary with climate, time of year, and quality of your lawn. We recommend that you experiment with both the cutting height and ground speed until you achieve the best cut. Start with a high cutting height and using progressively lower settings until you find a cutting height that is matched to your mowing conditions and preferences.

ATTACHING A TRAILER

The maximum weight of a towed trailer should be less than 200 lbs (91kg). Secure the trailer with a appropriately sized clevis pin (A, Figure 12) and clip

(B).

Excessive towed loads can cause loss of traction and loss of control on slopes. Reduce towed weight when operating on slopes. The surface being driven on greatly impacts traction and stability. Wet or slippery surfaces can greatly reduce traction and the ability to stop or turn. Carefully evaluate the surface conditions before operating the unit and trailer, and never operate on slopes greater than 10°. See SLOPE OPERATION and TOWED EQUIPMENT in the safety section of this manual for additional safety information.

A

B

Figure 12. Trailer Weight Recommendations

A.Clevis Pin

B.Clip

Figure 11. Mulching Action

24

www.ferrisindustries.com

Image 26
Contents Ferris Industries DescriptionModel Number Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Children Slope OperationTowed Equipment RIDE-ON Units EmissionsSafe Handling of Gasoline Service and MaintenanceMaintenance and Storage Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers IdentificationSafety Decals Safety DecalsOperational Safety Checks Safety Interlock SystemNorth American Safety Icons AIR Cooled Models only Seat Adjustment LeverIgnition Switch Control FunctionsParking Brake PTO Power Take Off SwitchHour Meter / Maintenance Reminder Throttle ControlLiquid Cooled Models only Water Temperature Gauge Never allow passengers to ride on the unit General Operating SafetyChecks Before Starting Pushing the Rider by Hand Starting the EngineStopping the Rider Forward Travel Practice Zero Turn Driving PracticeSmooth Travel Reverse Travel PracticeExecuting Turns Practice Turning Around a Corner Practice Turning In PlaceExecuting an End-Of-Row Zero Turn TurningHeight of Grass MowingMowing Recommendations Tall Grass Requires Incremental CuttingMowing Patterns When and How Often to MowMowing Methods Proper Broadcast MowingAttaching a Trailer Proper MulchingTo raise the roll bar Raise & Lower the Roll BARTo lower the roll bar Keep roll bar in the raised position and use seat beltTemporary Storage 30 Days Or Less StorageStarting After Long Term Storage Long Term Storage Longer Than 30 DaysEngine Maintenance Safety ItemsRider Maintenance Before Every Spring Each 100 250 Fall Use HoursFuel Filter Check Tire PressuresChecking / Adding Fuel Change OIL & FilterAir Cooled Models Check Hydraulic OIL LevelChange Hydraulic OIL Filter Liquid Cooled ModelsPressurized System Change Engine Coolant Clean Radiator & ScreenCheck Engine Coolant Level Oil LubricationGrease PivotsCleaning the Battery and Cables Liquid Cooled Models Battery MaintenanceCleaning the Battery and Cables Air Cooled Models Servicing the Mower Blades Removing the BladeTroubleshooting Warning Troubleshooting the RiderTroubleshooting the Mower Rider TroubleshootingTroubleshooting Common Cutting Problems StreakingSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment Adjustment Linkage Rod Neutral AdjustmentRETURN-TO-NEUTRAL Adjustment RH side shownParking Brake Adjustment Parking Brake Adjustment Brake Spring Adjustment NutTo adjust the upper mounting position Suspension AdjustmentTo adjust the spring pre-load To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment Outer Rod Deck Lift ROD Timing AdjustmentInner Rod 4 Locations Deck Leveling AdjustmentDeck Lift Spring Hydraulic Pump Drive Belt Replacement Mower Belt Replacement DeckCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Jump Starting With Auxiliary Booster BatteryJump Starting This HOOK-UP for Negative Ground VehiclesMake Certain Vehicles do not Touch Chassis DimensionsEngine TransmissionsFerris Limited Warranty Mower Deck Belts and BladesTractor