Ferris Industries 5900619, 5901170, 5900629 Deck Lift ROD Timing Adjustment, Inner Rod, Outer Rod

Page 44

Troubleshooting, Adjustment & Service

DECK LIFT ROD TIMING

ADJUSTMENT

Inner Rod

1. Park machine on a flat, level surface. Disengage the PTO, stop the engine and engage the parking

brake. Rear tires must be inflated to 18 psi (1,24 bar); front tires to 25 psi (1,72 bar).

2. To check the inner lift rod timing, measure and record the distance between the inner lift pivots and the inner rod pivots. Repeat for other side of unit. See Figure 37.

Measure

2nd

1st

Measure

2nd

1st

Troubleshooting

3.To check the outer lift rod timing, measure and record the distance between the outer lift pivots and the outer rod pivots. Repeat for other side of unit. See Figure 37.

4.If the measurements for the inner rods are equal, and the measurements for the outer rods are equal, no further adjustment is required. If the measurements are NOT equal (greater than 1/8” (3,17mm) difference), adjustment is required, continue with Step 5.

5.Lock the deck lift pedal in the 5” (12,7cm) position. Remove the cutting height adjustment pin and lower the mower deck.

6.To ensure that the deck is in the lowest position, push the pedal by hand towards the rear of the unit and install the height adjustment pin in the 3” (7.6cm) position to hold in place.

7.Block up the mower deck until all hanger chains are slack.

8.Refer to Figure 39. To adjust the inner lift rod, loosen the jam nut on the front ball joint then remove the 1/2” hardware fastening the ball joint the the lift pivot arm. Turn the ball joint clockwise to shorten the distance between the rod pivots or counterclockwise to lengthen the distance between the rod pivots. Reinstall the ball joint on the lift pivot arm and secure with the 1/2” hardware previously removed. Tighten the jam nut against the lift rod.

9.Refer to Figure 39. To adjust the inner lift rod, loosen the jam nut on the front ball joint then remove the 1/2” hardware fastening the ball joint the the lift pivot arm. Turn the ball joint clockwise to shorten the distance between the rod pivots or counterclockwise to lengthen the distance between the rod pivots. Reinstall the ball joint on the lift pivot arm and secure with the 1/2” hardware previously removed. Tighten the jam nut against the lift rod.

10.Remove blocks from under the mower deck.

11.Remove the the cutting height adjustment pin from in front of the deck lift pedal arm. Lift mower deck and reinstall adjustment pin in desired mowing height.

Outer Rod

Figure 37. Measure the Inner & Outer Lift Rods

Figure 38. Deck Lift Pedal & Pin Position

Inner Rod

Adjust Here

Adjust Here

Outer Rod

Figure 39. Adjust the Inner & Outer Lift Rods

42

www.ferrisindustries.com

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Ferris Industries DescriptionModel Number Date Purchased Table of Contents Operating Safety Slope Operation Roll Bar Use Fuel and Maintenance Preparation OperationTraining Slope Operation Towed Equipment RIDE-ON UnitsChildren EmissionsSafe Handling of Gasoline Service and MaintenanceMaintenance and Storage Roll BAR Instructions Operational WarningsInspection and Maintenance of the Roll BAR Seat Belt Identification Numbers IdentificationSafety Decals Safety DecalsOperational Safety Checks Safety Interlock SystemNorth American Safety Icons Seat Adjustment Lever Ignition SwitchAIR Cooled Models only Control FunctionsPTO Power Take Off Switch Hour Meter / Maintenance ReminderParking Brake Throttle ControlLiquid Cooled Models only Water Temperature Gauge Never allow passengers to ride on the unit General Operating SafetyChecks Before Starting Pushing the Rider by Hand Starting the EngineStopping the Rider Zero Turn Driving Practice Smooth TravelForward Travel Practice Reverse Travel PracticePractice Turning Around a Corner Practice Turning In Place Executing an End-Of-Row Zero TurnExecuting Turns TurningMowing Mowing RecommendationsHeight of Grass Tall Grass Requires Incremental CuttingWhen and How Often to Mow Mowing MethodsMowing Patterns Proper Broadcast MowingAttaching a Trailer Proper MulchingRaise & Lower the Roll BAR To lower the roll barTo raise the roll bar Keep roll bar in the raised position and use seat beltStorage Starting After Long Term StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysSafety Items Rider MaintenanceEngine Maintenance Before Every Spring Each 100 250 Fall Use HoursCheck Tire Pressures Checking / Adding FuelFuel Filter Change OIL & FilterCheck Hydraulic OIL Level Change Hydraulic OIL FilterAir Cooled Models Liquid Cooled ModelsPressurized System Change Engine Coolant Clean Radiator & ScreenCheck Engine Coolant Level Lubrication GreaseOil PivotsCleaning the Battery and Cables Liquid Cooled Models Battery MaintenanceCleaning the Battery and Cables Air Cooled Models Servicing the Mower Blades Removing the BladeTroubleshooting Warning Troubleshooting the RiderTroubleshooting the Mower Rider TroubleshootingTroubleshooting Common Cutting Problems StreakingSpeed Balancing Adjustment Seat AdjustmentGround Speed Control Lever Adjustment Neutral Adjustment RETURN-TO-NEUTRAL AdjustmentAdjustment Linkage Rod RH side shownParking Brake Adjustment Parking Brake Adjustment Brake Spring Adjustment NutTo adjust the upper mounting position Suspension AdjustmentTo adjust the spring pre-load To adjust pedal position Mowing Height AdjustmentFoot Pedal Adjustment Outer Rod Deck Lift ROD Timing AdjustmentInner Rod 4 Locations Deck Leveling AdjustmentDeck Lift Spring Hydraulic Pump Drive Belt Replacement Mower Belt Replacement DeckBattery Service Checking Battery VoltageCharging a Completely Discharged Battery Jump Starting With Auxiliary Booster BatteryJump Starting This HOOK-UP for Negative Ground VehiclesMake Certain Vehicles do not Touch Dimensions EngineChassis TransmissionsFerris Limited Warranty Mower Deck Belts and BladesTractor
Top Page Image Contents