Hayter Mowers 412G, 413G, 410G manual Securing Nuts & Bolts, Clutch Cable Adjustment, Lubrication

Page 12

MOWER MAINTENANCE

Securing Nuts & Bolts

Regularly check that all securing nuts and bolts are tight. Replace missing or damaged items immediately.

Clutch Cable Adjustment

At any time the operator feels that the machine is loosing drive:

1.Stop the engine.

2.Pull the machine backwards at the same time progressively engage the clutch lever until the rear rollers lock, at this point the clutch lever should be

60mm from the handlebar.

3.If the distance between the clutch lever and handlebar is less than 60mm regulate the engagement position with the black plastic cable adjuster. To regain the

60mm distance (Refer fig.28 & 29)

4.Note this is a temporary adjustment and at the nearest opportunity a service should be carried out to ensure the spring on the clutch cable attached to the gearbox clutch is set correctly. This adjustment should be done using the metal adjuster at the control with the plastic adjuster reset fully wound in. When the spring is set tighten the inner lock nut to secure position. (Refer

Lubrication

Lubricate the wheels, pivot points and linkages with engine oil every 25 operating hours.

Apply a good quality medium grease to the inner control cables at the point of entry and exit from their outer cas- ing.

Cutterblade Removal

Drain the fuel by running the engine until the fuel tank is empty and the engine stops. Remove the spark plug lead and allow the engine to cool. Turn the mower on its left hand side and ensure that the air cleaner side of the engine is uppermost. (Refer fig.32)

Firmly grip the end of the cutterblade with a gloved hand and remove the bolt, spring washer and distance piece securing the cutterblade with a 9/16” A/F spanner. (Refer fig.33)

To prevent accidents never work on the cutterblade unless the spark plug lead has been removed. The cutterblade has sharp edges. ALWAYS wear strong gloves to protect your hands when working on the cutterblade. DO NOT rotate tools towards the cutting edges to avoid the risk of injury should the tool slip. ALWAYS use genuine Hayter replacement parts.

The condition of the cutterblade and its mounting arrangement should be checked regularly for signs of wear or damage. Ensure that the cutterblade is not bent or cracked.

A damaged cutterblade that is out of balance will vibrate excessively and may break. DO NOT use an unbalanced cutterblade.

Regularly check that the bolt securing the cutterblade is tightened to the specified torque of 54Nm.

Replace the cutterblade every 2 years of sooner if excessively worn or damaged.

To prevent injury it is wise to seek assistance when turning the mower on its side.

Cutterblade Assembly

Assemble the cutterblade with the turned up edges facing towards the engine. Secure the cutterblade using the bolt (1), spring washer (2), and distance piece (3). (Refer fig.33)

figs.30 & 31)

Fig. 28

Fig. 29

Fig. 30

Fig. 31

Fig. 32

Fig. 33

60mm

Clutch lever fully engaged

1

Tighten the inner

nut when the cable

spring is set.

Metal adjuster

13mm extension

Clutch spring

1 2 3

12

Image 12
Contents Harrier Contents Introduction Specifications / Main Features Overall dimensionsSafety Precautions Maintenance & Storage Control SymbolsAssembling the Mower / Before Starting the Mower Operating the Mower Slopes Height Of CutGrassbag Without Grass CollectionOperating the Mower / Maintenance Schedule Non Grassed AreasEngine Detail Refer Mower Maintenance Clutch Cable Adjustment Cutterblade AssemblySecuring Nuts & Bolts LubricationCutterblade Sharpening StorageBattery Charging Code 412 only January FebruaryMarch AprilTrouble Shooting Problem Causes Corrective ActionWarrantynotes Limited WarrantyPage Page Service Record Customer Information