Pioneer VSX-53TX Manual: Resetting Your Stereo System

Using Other Functions

Resetting the Main Unit

The following operations allow you to reset the unit to the default settings.

	1	While holding down the TONE button
		press the STANDBY/ON button for
		about three seconds.
	2	When you see RESET? appear in the
		display, press the TONE – button. OK?
1	1	appears in the display, press TONE +.
1	1	When OK appears in the display all the settings,

including the speaker, surround sound settings and tuner settings, will be reset in the unit to the default settings.

Memo:

• When resetting the receiver make sure the MULTI-ROOM

feature is off.

• If the receiver is disconnected from a power source for

about a month or longer it will reset to the default

settings.

2 2

EXPERT

Page 79

Image 79

Pioneer VSX-53TX Resetting the Main Unit, Press the STANDBY/ON button for, About three seconds, When you see RESET? appear

Contents

Page Page Page Table of Contents Easy Setup Guide Preparation Surround Setup Basic Expert Audio Scaler HI BIT/HI Sampling FeaturesB fore You StartMultichannel Acoustic Calibration EQ System Mcacc 12V Trigger Loading the batteries Checking the Supplied AccessoriesPreparing the Remote Control Before You Start Inches 20 cm Receiver Installing the ReceiverOperating range of remote control unit Opening the Front Panel Home Theater The Basics EasDi playsSetup& ControlsGuidePart Digital Connections Hooking Up Your DVD Player and TV  Speaker terminals Speaker Connections Assigning the Digital Inputs Setting up the Main Unit Auto Surround Sound Setup Easy Setup Guide Part For loud test tones Check the speaker settings on the OSD Normal use Playing a DVD with Surround Sound Component video Connecting your TVComponent Video Input Default Settings Video Connecting a DVD player Connecting Video Components Connecting a Video Component to the Front Panel Connecting VCRs or DVRs Satellite tuner Connecting Satellite TV SAT Components  Audio cords Connecting Analog Audio Components Preparation Not a PCM-only output Connecting Digital Audio Components  Coaxial cords/Optical cables Digital Input Default Settings Using outdoor antennas Connecting the Radio Antennas AM loop antenna Connecting Speakers Speaker impedance Bi-wiring your speakers Speaker placement Power Connections AC OutletsPlacing Your Speakers Front Panel Displays& Controlsand Controls Setup MIC jack see Master Volume dialSignal Select button see SB CH Mode button see Remote Control EFFECT/CH SEL button Signal SEL button seeBASS/TREBLE buttons see Multi Operation button +/- buttons 16 ////ENTER buttons Master Volume +/- buttonsRemote Setup button TOP MENU/GUIDE button Display Back Panel Digital in terminals see AC Outlet switched, 100 W maxMULTI-ROOM & Source Remote in terminal see Speakers terminals see Trol Through the menus. When you haveSetting you want in a particular menu Turn on the receiver and your TV. Press If it isn’t use the  buttons to select it Surround Back SystemExit should be selected. Press the Enter button Use the  buttons to select Normal Normal SetupThrough the Normal setup menus When you have the setting you want Surround default setting is Small Speaker SettingFront default setting is Small Center default setting is Small Size Large or Small for each set With the  buttons chooseUse the  buttons to choose Number YES or NO, X1 or X2 Level Manual or AUTO. Select a Setting mode with the  buttonsChannel Level Isn’t use the  buttons to select Select each speaker channel with Speaker DistanceSpeaker Distance should be Select it. Press the Enter button Stereo and Multichannel Playback Choose a Listening Mode one of two waysIndicator Basic Operation Selecting the Input Signal Stereo modes Listening Modes THX Cinema 2PL II Movie 2PRO Logic II Movie Movie modes Surround mode 2PL II Music 2PRO Logic II Music Music modes Surround mode Adding/Adjusting the Effect in Dolby Pro Logic II Music Mode Adjusting the Effect of a Listening Mode Press the Acoustic EQ button Press Receiver Press the DNR button on the remote controlListening with Acoustic CAL EQ Digital Noise Reduction Digital NR Function Listening in Loudness Mode Listening in Midnight ModePress the Midnight button on the remote control Listening with Sound Delay Adjusting Bass and Treble This mode cannot be used with Multi CH in mode Listening in Audio Scaler mode Multi Channel In Playback Press the SB CH Mode button on Surround Back Channel ModePress the SB CH Mode button on the remote control Virtual Surround Back Mode Jack on the front of the receiver Dual Mono setting and playbackUsing Headphones Plug headphones into the Phones Video Select Adjusting the Brightness of the Display Dimmer Press the Tuner button Using the TunerUsing the TunerAutomatic and Manual Tuning MPX Mode Example Direct Access TuningTo cancel before inputting the frequency Press the Band button to select the band FM or AM Tune in the station you want Memorizing Frequently Used StationsPress the Enter button to input your choice Naming Memorized Stations Use the number buttons to select the channel you want Recalling Memorized StationsTo step through each channel in order Recalling Settings Stored in the Remote Control Setting Up the Remote Control to Control Other ComponentsRemoteDisplays & Controlontrols of Other Components Press the button to be programmed Programming Signals from Other Remote Controls Learning Mode CD/MD/CD-R/VCR/DVD/LD/DVD Recorder/Cassette Deck operations Using Remote Control with Other Components Return Cable TV/Satellite TV/Digital TV/TV operations Setting up the Direct Function Start recording tape deck, CD Recorder, VCR, etc Using Other FunctionsUsing Other FunctionsRecording from Audio/Video Components Turn on the receiver Second Zone Speaker System B Setup Connecting Additional Amplifiers Multi Room function Setup exampleMulti Room connections It isnt use the  buttons to select Using Other FunctionsUse the  buttons to select Multi ROOM. Press Enter Select the source with the Multi JOG Press the Control button to enter the control modeAdjust the volume You can adjust the volume level in the following range From the sub room, point the remote Press Volume +/- to adjustVolume Controlling the Multi Room system from the sub room Pioneer SR System Operating other Pioneer components Select a Multi Control button for this multi operation Multi Operations Performing Multi Operations Select a Multi Control button for Using System OFFSystem Off Press the Receiver button Resetting the Remote Control Press the STANDBY/ON button for Resetting the Main UnitWhen you see RESET? appear When OK appears in the display all the settings THX Cinema Setup Selected, if not use the  buttons to When youre finished use the Input ASSIGN. Press the Enter DIGITAL-IN Select should be Use the  buttons to assign a receiver function Assigning the Component Video InputsComponent video input you want to Reassign. Press the Enter button Function Rename 12V Trigger function Expert Setup Expert System Settings Crossover Network should be Crossover NetworkTo select and press Enter Fine Channel Level should be Use the  buttons to adjustAdjust the level of the channel using Fine Channel Level Distance of the left channel. Press Fine Channel DelayFine Channel Delay should be Adjust the distance of each channel using the  buttons Acoustic Calibration EQ EQ Auto Setting should beStart EQ Auto Setting When done select Exit if it’s not TOM 1 or Custom 2 as the destina Use the  buttons to select DataCOPY. Press Enter Use the  buttons to select CUS This explanation is for Custom 1 or Custom For explanation purposes Illustrations use ALL CH Adjust Use the  buttons to adjust Trim and press Enter To use the Data Check feature follow the steps here Tone and specify the bass peak level Start or Setting CANCEL. PressUse the buttons to adjust the test Bass Peak Level  buttons to select it, press Dynamic Range ControlRange Control should be OFF, MID or MAX. Press Enter Dolby Pro Logic Chart Comparing Dolby Pro Logic and Dolby Pro LogicDolby Dolby Digital DTS 96/24 DTS Neo6 Power Power does not turn on TroubleshootingOverheat blinks in the display and no sound is output Sound Setup Setup screen doesnt appearNo audio No sound is output when a To be something wrong with No sound output from one set of speakers No sound output from the subwoofer Considerable noise in radio broadcasts Other audio problems Input/display Video No image is output when aThere is no image coming Video jacks Cant record video Miscellaneous Remote controlShow 96kHz Other components cant be operated with the system remote DVD Preset Code Brands EIA Maintenance of External Surfaces Specifications TNMWF/03C00001 Printed

Pioneer How to Reset Your VSX 53TX and VSX 53 Stereo System

Models: VSX-53TX

Using Other Functions

Resetting the Main Unit

press the STANDBY/ON button for

about three seconds.

When you see RESET? appear in the

appears in the display, press TONE +.

When OK appears in the display all the settings,

Memo: