Heath Zenith manual Operating Instructions & Parts Manual 2LBL7, 2LBL8

Page 1

Operating Instructions & Parts Manual

2LBL7, 2LBL8

 

 

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply could result in personal injury and/or property damage! Save these instructions for future reference.

®Model 2LBL7: 50 Watt Metal Halide Patio Light

Model 2LBL8: 70 Watt High Pressure Sodium Patio Light

NOTE: All wiring must be run in accordance with the National Electrical Code (Canadian Electrical Code in Canada) through conduit or another acceptable means. Contact a qualified electrician if there is any question as to the suitability of the system.

Lamp in Fixture Contains Mercury. Dispose According to Local, State, or Federal Laws.

WARNING: Turn power off at the fuse or circuit breaker.

This fixture can be mounted on a wall with, or without using a flush- mounted junction box. Do not attempt to mount this fixture on a surface-mounted “Wet Location” junction box. Use the instructions below that apply to your application.

Installation Using A Junction Box

Note: If your junction box protrudes out of the wall slightly, you may want to use the enclosed gasket so less caulking is required.

1.Hold the Mounting Bracket and Gasket over the junction box. Thread the supply wires through the large hole in the back of the Mounting bracket. Select the holes in the mounting bracket that line up with the screw holes in the junction box. Make sure the bottom of the Mounting Bracket is level. Secure with the two #8 screws provided.

Installation Without A Junction Box

1.Select a location on a flat wall with structurally sound wood and from 5 to 25 feet from the ground. The wood should be at least one inch thick to safely secure the fixture.

2.Use the Mounting Bracket as a template. Hold it at the desired mounting location (making sure the bottom is level), and mark four mounting holes.

3.Use four #8 or #10 wood screws or galvanized deck screws at least 1 inch long (not provided) to secure the Mounting Bracket to the wall. It may be necessary to drill appropriate pilot holes if mounted to hardwood to avoid splitting.

4.Remove the knockout in the bottom of the Mounting Bracket, and bring your supply wires through this knockout using appropriate flexible conduit or other approved means of wiring.

Complete The Installation

1.Put the Temporary Pin through the holes in the Mounting Bracket.

2.This fixture must be grounded. Connect the supply ground wire to the green ground screw.You can also attach a bare or green “pigtail” to the green ground screw, then connect the ground pigtail to the supply ground when the other supply wires are connected.

3.Slide the fixture onto the Mounting Bracket, and allow the fixture to rest on the Temporary Pin.

4.Connect the fixture wires to the supply wires (black to black, white to white, and if a ground pigtail was added above, con-

nect this pigtail to the supply ground wire). Secure with the wire connectors provided.

5.Remove the Temporary Pin, and slide the fixture all the way down onto the Mounting Bracket making sure no wires get pinched.

6.Install the screw through the bottom of the Mounting Bracket and into the fixture housing. Tighten this screw.

7.Install lamp (provided). Lamp rating must match the rating of the fixture.

Model 2LBL7: 50 watt metal halide M110/O open rated lamp.

Model 2LBL8: 70 watt high pressure sodium type S62 lamp.

8.Caulk fixture mounting surface with silicone weather sealant.

To test operation during daylight, cover the photocontrol with black tape.Turn on the power.The light will take up to ten minutes to reach full brightness. Remove the tape from the photocontrol and your unit will operate automatically—on at dusk, off at dawn.

Photocontrol

Fixture

Ground

 

Screw

Temporary

Pin

Mounting

LampBracket

Gasket

(Optional)

HEA 012

598-1319-02

Printed in China

LPG-5659, LPG-5679

02/08

 

Page 1 Page 2
Image 1
Page 1 Page 2
Contents Installation Without a Junction Box Installation Using a Junction BoxComplete The Installation Operating Instructions & Parts Manual 2LBL7, 2LBL8Model 2LBL7 Ballast Assembly Replacement InstructionsBallast Ignitor LampBallast Ignitor Model 2LBL8Year limited warranty Instalación Usando una Caja de Empalme Manual de Instrucciones y Partes 2LBL7, 2LBL8Instalación Sin Una Caja de Empalme Complete la InstalaciónModelo 2LBL7 Instrucciones para el cambio del conjunto estabilizadorEstabilizador Encendedor. Retire con cuidado el encendedor y el es Modelo 2LBL8Garantía limitada a un 1 año Installation avec boîte de jonction Mode d’emploi et guide des pièces 2LBL7, 2LBL8Installation sans boîte de jonction Terminez l’installationModèle 2LBL7 Directives de remplacement du ballastDouille ’ampouleModèle 2LBL8 Garantie limitée d’un an

2LBL8, 2LBL7 specifications

Heath Zenith has long been a trusted name in the realm of home security and lighting solutions, and their models 2LBL7 and 2LBL8 exemplify the brand's commitment to quality, innovation, and functionality. These models are particularly popular for outdoor use, bringing together advanced technologies designed to enhance both safety and convenience.

One of the standout features of the Heath Zenith 2LBL7 and 2LBL8 is their dual function as both motion-activated lights and security fixtures. Equipped with a high-performance motion sensor, these lights are capable of detecting activity within a range of up to 70 feet, with an adjustable sensitivity setting to reduce the likelihood of false alarms from pets or passing vehicles. This makes them ideal for protecting entrances and driveways, enhancing visibility at night while also providing a deterrent to potential intruders.

In terms of illumination, both models utilize energy-efficient LED technology, which not only ensures a bright and effective lighting output but also contributes to energy savings. The lights have a color temperature of 5000K, delivering a daylight-like brightness that enhances clarity and visibility in outdoor spaces. Additionally, they are designed to provide a significant number of lumens, ensuring that even large areas are well-lit when motion is detected.

Another notable characteristic of the Heath Zenith 2LBL7 and 2LBL8 is their weather-resistant design. Constructed with durable materials, these lights are built to withstand a range of environmental conditions, including rain, snow, and extreme temperatures. This makes them perfectly suitable for various outdoor settings, from residential patios to commercial properties.

Installation is made easier with the included mounting hardware and straightforward instructions, which allow homeowners and business owners alike to set up these fixtures with minimal hassle. The adjustable heads on both models also enable precise direction of the light, optimizing coverage for specific areas as needed.

Overall, the Heath Zenith 2LBL7 and 2LBL8 embody a perfect blend of functionality, efficiency, and durability. With their advanced motion sensing capabilities, energy-efficient LEDs, and weather-resistant construction, they serve as reliable options for enhancing outdoor security and lighting solutions, making them a solid investment for any property owner looking to boost safety and convenience.
Top Page Image Contents