Husqvarna 1151438-95, 345e EPA III Fueling, Fuel safety, Transport and storage, Long-term storage

Page 20

FUEL HANDLING

•Contact your service agent when choosing chain oil.

Fueling

WARNING! Taking the following

!precautions, will lessen the risk of fire:

Do not smoke and do not place any hot objects in the vicinity of fuel.

Always stop the engine and let it cool for a few minutes before refuelling.

When refuelling, open the fuel cap slowly so that any excess pressure is released gently.

Tighten the fuel cap carefully after refuelling.

Always move the machine away from the refuelling area before starting.

Clean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at least once a year. Contamination in the tanks causes malfunction. Make sure the fuel is well mixed by shaking the container before refuelling. The capacities of the chain oil tank and fuel tank are carefully matched. You should therefore always fill the chain oil tank and fuel tank at the same time.

WARNING! Fuel and fuel vapor are highly

! flammable. Take care when handling fuel and chain oil. Be aware of the risks of fire, explosion and those associated with inhalation.

Fuel safety

•Never refuel the machine while the engine is running.

•Make sure there is plenty of ventilation when refuelling or mixing fuel (gasoline and 2-stroke oil).

•Move the machine at least 10 ft (3 m) from the refuelling point before starting it.

Min. 3 m (10 ft)

•Never start the machine:

1If you have spilled fuel or chain oil on the machine. Wipe off the spillage and allow remaining fuel to evaporate.

2If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water.

3If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.

WARNING! Never use a machine with

! visible damage to the spark plug guard and ignition cable. A risk of sparking arises, which can cause a fire.

Transport and storage

•Always store the chain saw and fuel so that there is no risk of leakages or fumes coming into contact with sparks or naked flames from electrical equipment, electric motors, relays/switches, boilers and the like.

•Always store fuel in an approved container designed for that purpose.

•For longer periods of storage or for transport of the chain saw, the fuel and chain oil tanks should be emptied. Ask where you can dispose of waste fuel and chain oil at your local gas station.

•Ensure the machine is cleaned and that a complete service is carried out before long-term storage.

•The bar guard must always be fitted to the cutting attachment when the machine is being transported or in storage, in order to prevent accident contact with the sharp chain. Even a non-moving chain can cause serious cuts to yourself or persons you bump into with an exposed chain.

Long-term storage

Empty the fuel/oil tanks in a well ventilated area. Store the fuel in approved cans in a safe place. Fit the bar guard. Clean the machine. See instructions under the heading Maintenance schedule.

20 – English

Page 19 Page 21
Image 20
Page 19 Page 21
Contents EPA III TrioBrake Symbols in the operator’s manual KEY to SymbolsSymbols on the machine You will find the following labels on your chain saw EPAContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?Always use common sense General Safety PrecautionsBefore using a new chain saw Chain brake and front hand guard Machine′s safety equipmentPersonal protective equipment General Safety Precautions Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesSharpening your chain and adjusting depth gauge setting Cutting equipment designed to reduce kickbackGeneral advice on adjusting depth gauge setting If the depth gauge setting is too largeAdjustment of depth gauge setting Tensioning the chainBar and cause serious or even fatal injury 346XP TrioBrake, 353 TrioBrakeChecking chain lubrication Lubricating cutting equipmentFilling with chain oil Checking wear on cutting equipment Chain drive sprocketNeedle bearing lubrication Assembly Fitting the bar and chain346XP TrioBrake, 353 TrioBrake 345e TrioBrakeAssembly Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Limbing Basic cutting techniqueTerms Cutting Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionCutting the trunk into logs How to avoid kickbackWhat is kickback? General MaintenanceCarburetor adjustment Correctly adjusted carburetor High speed jet HChecking the right-hand brake trigger Checking the brake triggerMuffler Starter Changing a broken or worn starter cordTensioning the recoil spring 345eReplacement of broken recoil and drive disc springs Air filterSpark plug Fitting the starterAdjustment of the oil pump When making adjustmentsLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature 0C 32F or colderHeated handles Electrical carburetor heatingMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gauges050/1,3 mm 058/1,5 mmFederal Emission Control Warranty Statement ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautions1151438-95
Top Page Image Contents